ASTM D 1894 : 2011 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
Hardcopy , PDF
11-11-2014
English
01-09-2011
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| Supersedes |
1.1 This test method covers determination of the coefficients of starting and sliding friction of plastic film and sheeting when sliding over itself or other substances at specified test conditions. The procedure permits the use of a stationary sled with a moving plane, or a moving sled with a stationary plane. Both procedures yield the same coefficients of friction values for a given sample.
Note 1—For the frictional characteristics of plastic films partially wrapped around a cylinder, or capstan, see Test Method G143 under the jurisdiction of ASTM Subcommittee G02.50.
1.2 Test data obtained by this test method is relevant and appropriate for use in engineering design.
1.2.1 As an option to this test, coefficient of friction may be run at temperatures other than 23°C by heating only the plane while the sled is at ambient temperature.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see the end of 6.5.
Note 2—This test method is not equivalent to ISO 8295–1995, and results cannot be directly compared between the two methods.
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM F 2097 : 2016 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM D 378 : 2010 : R2016 | Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 4020 : 2018 | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials |
| ASTM E 1549/E1549M : 2013 : R2016 | Standard Specification for ESD Controlled Garments Required in Cleanrooms and Controlled Environments for Spacecraft for Non-Hazardous and Hazardous Operations |
| ASTM D 1894 : 2014 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM D 5047 : 2017 | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM D 8195 : 2018 | Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 7027 : 2013 | Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.