• Shopping Cart
    There are no items in your cart

ASTM D 2171/D2171M : 2018

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

Available format(s)

Hardcopy , PDF

Superseded date

21-11-2022

Language(s)

English

Published date

19-12-2018

€67.30
Excluding VAT

This test method covers procedures for the determination of the apparent viscosity of asphalt binder by vacuum capillary viscometers at 60 °C [140 °F].

Committee
D 04
DocumentType
Test Method
Pages
10
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This test method covers procedures for the determination of the apparent viscosity of asphalt binder by vacuum capillary viscometers at 60 °C [140 °F]. It is applicable to materials having viscosities in the range from 0.0036 to over 20 000 Pa·s [0.036 to over 200 000 P].

Note 1:This test method is suitable for use at other temperatures, but the precision is based on determinations on asphalt binders at 60 °C [140 °F].

Note 2:Modified asphalt binders or asphalt binders that have been conditioned or recovered are typically non-Newtonian under the conditions of this test. The apparent viscosity for non-Newtonian asphalt binders varies with shear rate. When the flow is non-Newtonian in a capillary tube, the shear rate determined using this test method may be invalid. The presence of non-Newtonian behavior for the test conditions of this test can be verified by measuring the viscosity with viscometers having different-sized capillary tubes or with different pressure heads. The defined precision limits in Section 11 may not be applicable to non-Newtonian asphalt binders. Test Method D4957 may be a more applicable method for testing non-Newtonian asphalts.

1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.3Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) or Safety Data Sheet (SDS) for details and the EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law.

1.4The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 2872 : 2022 Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
ASTM D 4989/D4989M : 1990 : REV A : R2021 Standard Test Method for Apparent Viscosity (Flow) of Roofing Bitumens Using the Parallel Plate Plastometer
ASTM D 2027/D2027M : 2019 Standard Specification for Cutback Asphalt (Medium-Curing Type)
ASTM D 3381/D3381M : 2018 Standard Specification for Viscosity-Graded Asphalt Binder for Use in Pavement Construction
ASTM D 1754/D1754M : 2020 Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
ASTM D 6626 : 2015 : R2021 Standard Specification for Performance-Graded Trinidad Lake Modified Asphalt Binder
ASTM D 3791/D3791M : 2011 : R2018 Standard Practice for Evaluating the Effects of Heat on Asphalts
ASTM D 2028/D2028M : 2015 : R2021 : EDT 1 Standard Specification for Cutback Asphalt (Rapid-Curing Type)
ASTM D 4887/D4887M : 2011 : R2021 : EDT 1 Standard Practice for Preparation of Viscosity Blends for Hot Recycled Asphalt Materials

ASTM D 3666 : 2013 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM E 11 : 2020 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM D 4957 : 2008 Standard Test Method for Apparent Viscosity of Asphalt Emulsion Residues and Non-Newtonian Bitumens by Vacuum Capillary Viscometer (Withdrawn 2017)
ASTM D 3666 : 2011 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2009 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 8 : 2022 : REV A Standard Terminology Relating to Materials for Roads and Pavements
ASTM E 11 : 2022 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM E 77 : 2014 : EDT 1 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 8 : 2022 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 3666 : 2005 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2003 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2000 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : EDT 2 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 4957 : 1995 Standard Test Method for Apparent Viscosity of Asphalt Emulsion Residues and Non-Newtonian Bitumens by Vacuum Capillary Viscometer (Withdrawn 2005)
ASTM D 8 : 2021 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 3666 : 2016 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2003 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 8 : 2019 Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 3666 : 2001 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 4957 : 2018 Standard Test Method for Apparent Viscosity of Asphalt Emulsion Residues and Non-Newtonian Asphalts by Vacuum Capillary Viscometer
ASTM D 3666 : 2006 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 8 : 2020 : REV A Standard Terminology Relating to Materials for Roads and Pavements
ASTM D 3666 : 2004 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM E 77 : 1998 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 3666 : 2005 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM E 77 : 2014 : R2021 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 3666 : 2007 : REV A : EDT 1 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2009 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2002 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.