ASTM D 2256/D2256M : 2021
Current
The latest, up-to-date edition.
Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method
Hardcopy , PDF
English
17-08-2021
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 13
|
| DocumentType |
Test Method
|
| Pages |
13
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers the determination of tensile properties of monofilament, multifilament, and spun yarns, either single, plied, or cabled with the exception of yarns that stretch more than 5.0 % when tension is increased from 0.05 to 1.0 cN/tex [0.5 to 1.0 gf/tex].
1.2This test method covers the measurement of breaking force and elongation of yarns and includes directions for the calculation of breaking tenacity, initial modulus, chord modulus, and breaking toughness.
1.2.1Options are included for the testing of specimens in: (A) straight, (B) knotted, and (C) looped form.
1.2.2Conditions of test are included for the testing of specimens that are: (1) conditioned air, (2) wet, not immersed, (3) wet, immersed, (4) oven-dried, (5) exposed to elevated temperature, or (6) exposed to low temperature.
Note 1:Special methods for testing yarns made from specific fibers; namely, glass, flax, hemp, ramie, and kraft paper and for specific products; namely, tire cords and rope, have been published: Test Methods D885, and Specification D578.
Note 2:For directions covering the determination of breaking force of yarn by the skein method refer to Test Method D1578.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2848 : 2021 | Standard Specification for Medical-Grade Ultra-High-Molecular-Weight Polyethylene Yarns |
| ASTM D 2644 : 2012 : R2018 | Standard Tolerances for Yarns Spun on the Woolen System |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM F 3510 : 2021 | Standard Guide for Characterizing Fiber-Based Constructs for Tissue-Engineered Medical Products |
| ASTM D 204 : 2002 : R2021 | Standard Test Methods for Sewing Threads |
| ASTM D 578/D578M : 2018 | Standard Specification for Glass Fiber Strands |
| ASTM D 2645 : 2007 : R2018 | Standard Tolerances for Yarns Spun on the Cotton or Worsted Systems |
| ASTM D 1578 : 1993 : R2016 | Standard Test Method for Breaking Strength of Yarn in Skein Form |
| ASTM D 123 : 2019 | Standard Terminology Relating to Textiles |
| ASTM D 2904 : 1997 : R2002 | Standard Practice for Interlaboratory Testing of a Textile Test Method that Produces Normally Distributed Data (Withdrawn 2008) |
| ASTM D 123 : 2023 | Standard Terminology Relating to Textiles |
| ASTM D 1578 : 1993 : R2022 | Standard Test Method for Breaking Strength of Yarn in Skein Form |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.