ASTM D 2275 : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
28-04-2022
English
11-12-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 10.01, 2015 Describes solid electrical insulating materials for use at commercial power frequencies with respect to their voltage endurance under the action of corona.
| Committee |
D 09
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method determines the voltage endurance of solid electrical insulating materials for use at commercial power frequencies under the action of corona (see Note 1). This test method is more meaningful for rating materials with respect to their resistance to prolonged ac stress under corona conditions for comparative evaluation between materials.
Note 1:The term “corona” is used almost exclusively in this test method instead of “partial discharge,” because it is a visible glow at the edge of the electrode interface that is the result of partial discharge. Corona, as defined in Terminology D1711, is “visible partial discharges in gases adjacent to a conductor.”
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.
| ASTM D 5047 : 2017 : REDLINE | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| IEEE 1133-1988 | IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications |
| ASTM D 3756 : 1997 : R2010 | Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields |
| IEEE DRAFT 434 : D10 2006 | FUNCTIONAL EVALUATION OF INSULATION SYSTEMS FOR AC ELECTRIC MACHINES RATED 2300 V AND ABOVE |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ANSI/NEMA FI 3:2004 | Calendered Aramid Papers Used for Electrical Insulation |
| IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
| ASTM D 3019 : 1994 : R2007 | Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Asbestos Fibered |
| IEEE 434-2006 | IEEE Guide for Functional Evaluation of Insulation Systems for AC Electric Machines Rated 2300 V and Above |
| ASTM D 1868 : 2013 : REDLINE | Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems |
| ASTM D 6097 : 2016 : REDLINE | Standard Test Method for Relative Resistance to Vented Water-Tree Growth in Solid Dielectric Insulating Materials |
| ASTM D 3018/D3018M : 2011 | Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules |
| ASTM D 3756 : 1997 | Standard Test Method for Evaluation of Resistance To Electrical Breakdown By Treeing In Solid Dielectric Materials Using Diverging Fields |
| ASTM ES 19 : 1991 | Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration (Withdrawn 1994) |
| ASTM D 3756 : 1997 : R2004 | Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| IEC 60343:1991 | Recommended test methods for determining the relative resistance of insulating materials to breakdown by surface discharges |
| ASTM D 1711 : 2015 : REDLINE | Standard Terminology Relating to Electrical Insulation |
| ASTM D 3382 : 2013 : REDLINE | Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques |
| ASTM D 1868 : 2013 : REDLINE | Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.