ASTM D 2394 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring
Hardcopy , PDF
23-08-2022
English
31-08-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.These test methods cover procedures for measuring the performance of finish flooring under the following service loadings and conditions:
| Committee |
D 07
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1These test methods cover procedures for measuring the performance of finish flooring under the following service loadings and conditions:
| Section | |
| Loading Tests | |
| Concentrated Loading | 7 |
| Floor Surface Indentation from Small Area Loads | 12 |
| Falling-Ball Indentation | 18 |
| Rolling Load | 23 |
| Mechanical Tests | |
| Abrasion Resistance | 28 |
| Coefficient of Friction | 33 |
| Moisture Tests | |
| Surface Wetting | 38 |
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7031 : 2011 : R2019 | Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products |
| ASTM G 115 : 2010 : R2018 | Standard Guide for Measuring and Reporting Friction Coefficients |
| ASTM C 1325 : 2019 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM D 5456 : 2019 | Standard Specification for Evaluation of Structural Composite Lumber Products |
| ASTM D 7032 : 2017 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
| ASTM C 1325 : 2022 | Standard Specification for Fiber-Mat Reinforced Cementitious Backer Units |
| ASTM D 5456 : 2021 : EDT 1 | Standard Specification for Evaluation of Structural Composite Lumber Products |
| ASTM D 7032 : 2021 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
| ASTM D 1037 : 2006 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
| ASTM D 1037 : 2012 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
| ASTM D 1037 : 1999 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
| ASTM D 1037 : 2006 : REV A | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
| ASTM D 1037 : 1978 | Standard Methods of Evaluating the Properties of Wood-Base Fiber and Particle Panel Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.