ASTM D 2444 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
Available format(s)
Hardcopy , PDF
Superseded date
13-09-2019
Superseded by
Language(s)
English
Published date
15-11-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
F 17
|
| DocumentType |
Standard Practice
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers the determination of the impact resistance of thermoplastic pipe and fittings under specified conditions of impact by means of a tup (falling weight). Three interchangeable striking noses are used on the tup, differing in geometrical configuration. Two specimen holders are described.
Note 1:Appendix X1 shows the procedure to determine impact strength.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 758 : 2014 : R2019 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
| ASTM F 1732 : 2012 : R2018 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material |
| ASTM F 2618 : 2019 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM F 2987 : 2012 : R2018 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications (Withdrawn 2024) |
| ASTM D 2852 : 2016 | Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings (Withdrawn 2022) |
| ASTM F 2763 : 2016 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 810 : 2012 : R2018 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM F 1504 : 2014 | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| ASTM F 1760 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
| ASTM F 628 : 2012 : EDT 3 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021) |
| ASTM F 3128 : 2019 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
| ASTM F 1412 : 2016 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 480 : 2014 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM F 949 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM F 2986 : 2012 : R2017 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| ASTM F 2176 : 2017 | Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct (Withdrawn 2024) |
| ASTM D 2241 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| ASTM G 125 : 2000 : R2015 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| ASTM D 3034 : 2016 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM F 1483 : 2017 | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM F 1673 : 2010 : R2016 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
| ASTM F 2658 : 2007 : R2019 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2306/F2306M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM F 794 : 2003 : R2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| ASTM F 758 : 2014 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
| ASTM D 2846/D2846M : 2019 : REV A | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems |
| ASTM F 2562/F2562M : 2015 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM F 1499 : 2017 | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| ASTM F 1336 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM F 2817 : 2013 : R2019 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair |
| ASTM D 2729 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 512 : 2012 : R2017 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
| ASTM F 725 : 2003 : R2018 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| ASTM F 891 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM F 679 : 2016 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| ASTM F 2390 : 2012 : R2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| ASTM F 2881/F2881M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 1871 : 2018 | Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM F 1901 : 2016 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM F 1488 : 2014 : R2019 | Standard Specification for Coextruded Composite Pipe |
| ASTM F 2158 : 2008 : R2016 | Standard Specification for Residential Central-Vacuum Tube and Fittings |
| ASTM F 3371 : 2019 | Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications |
| ASTM F 2947/F2947M : 2019 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2648/F2648M : 2017 | Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications |
| ASTM F 667/F667M : 2016 | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.