ASTM D 2471 : 1999
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Test Method for Gel Time and Peak Exothermic Temperature of Reacting Thermosetting Resins (Withdrawn 2008)
Hardcopy , PDF
30-09-2008
English
10-11-1999
CONTAINED IN VOL 08.02, 2005 Establishes the time from the initial mixing of the reactants of a thermosetting plastic composition to the time when solidification begins.
Committee |
D 20
|
DocumentType |
Test Method
|
Pages |
3
|
PublisherName |
American Society for Testing and Materials
|
Status |
Withdrawn
|
1.1 This test method covers the determination of the time from the initial mixing of the reactants of a thermosetting plastic composition to the time when solidification commences, under conditions approximating the conditions of use. This test method also provides a means for measuring the maximum temperature reached by a reacting thermosetting plastic composition, as well as the time from initial mixing to the time when this peak exothermic temperature is reached. This test method is limited to reacting mixtures exhibiting gel times greater than 5 min.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1-There is no similar or equivalent ISO standard.SAE AMS 2980/4 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 4 - PURCHASING SPECIFICATION - RESIN |
MIL-M-48245 Revision B:1988 | MOLDING COMPOUND, HOUSING |
MIL C 47257 : C | COMPOUND, EPOXY, FILAMENT WINDING |
SAE AMS 2950/1 : 2008 | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
ASTM F 602 : 2009 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
SAE AMS 2980/1 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 1 - GENERAL REQUIREMENTS |
SAE AMS 3733 : 2015 | POTTING COMPOUND, EPOXY, TWO PART, HIGHLY FILLED, HEAT CURE, HIGH COMPRESSIVE STRENGTH |
ASTM D 5364 : 2014 : R2019 | Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units |
ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
MIL-I-16923 Revision H:1991 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, EPOXY |
MIL-P-46067 Revision B:1977 | PLASTIC EMBEDDING COMPOUND, EPOXY RESIN SYSTEM |
MMM-A-1931 Base Document:1975 | ADHESIVE EPOXY SILVER FILLED, CONDUCTIVE |
AASHTO MP 35 : 2018 | SPECIFICATION FOR THIN OVERLAY TREATMENTS USING A BINDER RESIN SYSTEM AND AGGREGATE FOR CONCRETE SURFACES |
ASTM F 641 : 2009 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
MIL C 81904 : B | COATING COMPOUND, THERMAL INSULATION, ABLATIVE |
SAE ARP 5144 : 2017 | HEAT APPLICATION FOR THERMOSETTING RESIN CURING |
ASTM F 602 : 2009 : R2014 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
IPC J STD 030 : A | SELECTION AND APPLICATION OF BOARD LEVEL UNDERFILL MATERIALS |
ASTM F 602 : 2009 : R2015 | Standard Criteria for Implantable Thermoset Epoxy Plastics (Withdrawn 2024) |
MMM-A-1754 Base Document:1973 | ADHESIVE AND SEALING COMPOUND EPOXY METAL FILLED |
MIL-R-24719 Base Document:1989 | RESINS, VINYL ESTER, LOW PRESSURE LAMINATING |
ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
SAE AMS 2950/1 : 2008(R2019) | PASTE ADHESIVE FOR CORE RESTORATION - PART 1: GENERAL REQUIREMENTS |
ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.