ASTM D 2486 : 2017 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Methods for Scrub Resistance of Wall Paints
English
01-06-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 06.02, 2017 Defines a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as 'scrub resistance.'
| Committee |
D 01
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1These test methods cover a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as “scrub resistance.”
1.2Two test methods are covered as follows:
1.2.1Test Method A—Cycles-to-failure obtained on test paint.
1.2.2Test Method B—Ratio expressed as a percentage of cycles-to-failure obtained on the test paint to that obtained on a concurrent run with a known reference paint.
1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| TT-P-1952 Revision F:2015 | PAINT, TRAFFIC AND AIRFIELD MARKING, WATERBORNE |
| A-A-3126 Base Document:1972 | COATING SYSTEM: TILE-LIKE HIGH PERFORMANCE ARCHITECTURAL |
| MIL A 3316 : C | ADHESIVE, FIRE RESISTANT, THERMAL INSULATION |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 6736 : 2008 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 6900 : 2010 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
| ASTM E 1797 : 2012 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| TT-P-29 Revision K:1991 | PAINT, LATEX |
| CGSB-1.60 : 1997 | INTERIOR ALKYD GLOSS ENAMEL |
| TT-P-001957 Base Document:1984 | PAINT, LATEX (BACTERIOSTATIC AND FUNGISTATIC) |
| ASTM D 3730 : 2017 : REDLINE | Standard Guide for Testing High-Performance Interior Architectural Wall Coatings |
| TT-P-1510 Revision A:1975 | PAINT, LATEX, EXTERIOR, FOR WOOD SURFACES, WHITE AND TINTS |
| TT-P-650 Revision D:1988 | PRIMER COATING, LATEX BASE, INTERIOR, WHITE (FOR GYPSUM WALLBOARD, OR PLASTER) |
| ASTM D 3927 : 1987 | Guide for State and Institutional Purchasing of Paint (Withdrawn 1991) |
| STANAG 2836 : 0 | REMOVABLE PAINTS FOR CAMOUFLAGE |
| CGSB 1.216 : 1997 | EXTERIOR WATER-BORNE GLOSS ENAMEL |
| ASTM C 744 : 2016 : REDLINE | Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units |
| TT-P-002119 Base Document:1980 | PAINT, LATEX BASE, HIGH TRAFFIC AREA, FLAT AND EGGSHELL FINISH (LOW LUSTRE), (FOR INTERIOR USE) |
| CGSB-1.211 : 95 AMD 1 99 | COATING SYSTEMS FOR MARINE FLOATING NAVIGATIONAL AIDS (BUOYS) |
| ASTM D 5324 : 2016 : REDLINE | Standard Guide for Testing Water-Borne Architectural Coatings |
| ASTM D 6763 : 2016 : REDLINE | Standard Guide for Testing Exterior Wood Stains and Clear Water Repellents |
| ASTM D 3323 : 1980 : R1988 : EDT 1 | Guide for Testing Interior Solvent-Thinned Flat Wall Paints (Withdrawn 1993) |
| ASTM D 4213 : 2008 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D 4213 : 2008 : R2012 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM F 793/F793M : 2015 : REDLINE | Standard Classification of Wall Coverings by Use Characteristics |
| A-A-3185 Base Document:2001 | PAINT, LATEX (CONTAINING POST-CONSUMER MATERIAL) |
| TT P 001952 : C | PAINT, TRAFFIC AND AIRFIELD MARKING, WATERBORNE |
| A-A-3058 Base Document:1996 | PAINT, INTERIOR, FIRE RETARDANT |
| CGSB 1.138 : 1997 | EXTERIOR LATEX FLAT PAINT |
| ASTM E 1795 : 2017 : REDLINE | Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| ASTM E 1797 : 2012 : R2017 : EDT 1 | Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings |
| CGSB-1.208 : 1999 | MARINE INTERIOR WATER-BORNE GLOSS ENAMEL |
| ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
| ASTM E 2136 : 2004 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Durability |
| TT-C-001951 Base Document:1976 | COATING, CLEAR (SATIN FINISH), POLYURETHANE, LATEX, FOR INTERIOR USE |
| CGSB-1.73 : 1997 | EXTERIOR AND INTERIOR ENAMEL FOR FLOORS |
| ASTM D 6736 : 2008 : R2013 | Standard Test Method for Burnish Resistance of Latex Paints |
| ASTM D 6900 : 2010 : R2015 | Standard Test Method for Wet Adhesion of Latex Paints to a Gloss Alkyd Enamel Substrate |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.