ASTM D 2632 : 2015 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Method for Rubber Property—Resilience by Vertical Rebound
English
01-08-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 09.01, 2016 Defines the determination of impact resilience of solid rubber from measurement of the vertical rebound of a dropped mass.
| Committee |
D 11
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1This test method covers the determination of impact resilience of solid rubber from measurement of the vertical rebound of a dropped mass.
1.2This test method is not applicable to the testing of cellular rubbers or coated fabrics.
1.3A standard test method for impact resilience and penetration of rubber by a rebound pendulum is described in Test Method D1054.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-M-24476 Revision B:1993 | MOUNT, RESILIENT, TYPES 7M5O, 6M15O, 6M45O AND 6M9OO |
| ZZ-R-765 Revision E:1991 | RUBBER, SILICONE; RUBBER SHEET SOLID |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 3847 : 2001 : R2012 | Standard Practice for Rubber—Directions for Achieving Subnormal Test Temperatures |
| ASTM D 3847 : 2001 | Standard Practice for Rubber-Directions for Achieving Subnormal Test Temperatures |
| ASTM D 3847 : 2001 : R2018 | Standard Practice for Rubber—Directions for Achieving Subnormal Test Temperatures |
| ASTM D 3489 : 2017 : REDLINE | Standard Test Methods for Microcellular Urethane Materials |
| SAE J 2884 : 2014 | THERMOSET ELASTOMER SPECIFICATION SYSTEM |
| MIL-PRF-32407 Revision A:2016 | MOUNTS, RESILIENT (SURFACE SHIP APPLICATION) |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| SAE AMS3349D | SILICONE (VMQ) RUBBER, 1100 PSI (7.58 MPA) TENSILE STRENGTH, HIGH RESILIENCY, 65 - 75 |
| MIL-DTL-19863 Revision E:2018 | Mount, Resilient: Type 5B5,000H |
| MIL-R-83283 Revision A:1991 | RUBBER, SILICONE, HIGH STRENGTH, CABIN PRESSURE SEAL MATERIAL, DIAPHRAGM TYPE |
| SAE AMS R 83283 : 2014 | RUBBER SILICONE, HIGH STRENGTH, CABIN PRESSURE SEAL MATERIAL, DIAPHRAGM TYPE |
| MIL-DTL-21649 Revision D:2017 | MOUNT, RESILIENT, TYPE 5M10,000-H |
| MIL M 21649 : C | MOUNT, RESILIENT, TYPE 5M1O,OOO-H |
| ASTM D 1056 : 2014 : REDLINE | Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber |
| A-A-59001 Revision A:2012 | BATTERBOARD, SYNTHETIC |
| SAE AMS3348D | SILICONE (VMQ) RUBBER 1150 PSI (7.93 MPA) TENSILE STRENGTH, HIGH RESILIENCY 25 - 35 |
| CSA Z262.4 : 2000 | ICE HOCKEY PUCKS |
| ASTM D 3847 : 2001 : R2007 | Standard Practice for Rubber-Directions for Achieving Subnormal Test Temperatures |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3183 : 201 | PRACTICE FOR RUBBER - PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS |
| ASTM D 1349 : 2014 : REDLINE | Standard Practice for Rubber—Standard Conditions for Testing |
| ASTM D 832 : 2007 : R2018 | Standard Practice for Rubber Conditioning For Low Temperature Testing |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ASTM D 3182 : 2016 : REDLINE | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1566 : 2015 : REDLINE | TERMINOLOGY RELATING TO RUBBER |
| ASTM D 4483 : 2014-02 | PRACTICE FOR EVALUATING PRECISION FOR TEST METHOD STANDARDS IN THE RUBBER AND CARBON BLACK MANUFACTURING INDUSTRIES |
| ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.