ASTM D 2700 : 2024 : REV A
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
Hardcopy , PDF
20-08-2024
English
06-05-2024
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
59
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested in a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend that matches the knock intensity of the sample fuel establishes the Motor octane number.
1.2The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40 to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor octane number range.
1.3The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.
1.4For purposes of determining conformance with all specified limits in this standard, an observed value or a calculated value shall be rounded “to the nearest unit” in the last right-hand digit used in expressing the specified limit, in accordance with the rounding method of Practice E29.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For more specific hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 8291 : 2024 | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 8275 : 2022 | Standard Specification for Gasoline-like Test Fuel for Compression-Ignition Engines |
ASTM D 6709 : 2024 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine) |
ASTM D 6593 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 7719 : 2021 : REV A | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel |
ASTM D 4814 : 2024 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7547 : 2023 | Standard Specification for Hydrocarbon Unleaded Aviation Gasoline |
ASTM D 1094 : 2024 | Standard Test Method for Water Reaction of Aviation Fuels |
ASTM D 7960 : 2021 | Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components |
ASTM D 8111 : 2023 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 6812 : 2004 : REV A : R2019 | Standard Practice for Ground-Based Octane Rating Procedures for Turbocharged/Supercharged Spark Ignition Aircraft Engines |
ASTM D 8340 : 2022 | Standard Practice for Performance-Based Qualification of Spectroscopic Analyzer Systems |
ASTM D 6984 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine |
ASTM D 910 : 2024 | Standard Specification for Leaded Aviation Gasolines |
ASTM D 8076 : 2021 : REV B | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
ASTM D 2699 : 2024 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7826 : 2023 : REV B | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 6424 : 2004 : REV A : R2019 | Standard Practice for Octane Rating Naturally Aspirated Spark Ignition Aircraft Engines |
ASTM D 6227 : 2024 | Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component |
ASTM D 1310 : 2014 : R2021 | Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus |
ASTM D 7320 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 2885 : 2021 | Standard Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique |
ASTM D 8434 : 2021 | Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Organo-metallic Additive |
ASTM D 8291 : 2023 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 3703 : 2018 : R2024 | Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels |
ASTM D 4175 : 2023 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 3703 : 2018 | Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels |
ASTM D 4175 : 2024 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2024 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.