Skip to content
Please enter a keyword to search

  • ASTM D 2726/D2726M : 2019

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-05-2021

    Language(s):  English

    Published date:  12-03-2019

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This test method covers the determination of bulk specific gravity and density of specimens of compacted asphalt mixtures.

    1.2This test method should not be used with samples that contain open or interconnecting voids or absorb more than 2.0 % of water by volume, or both, as determined in 11.3.

    1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 04
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 6927 : 2022 Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures
    ASTM D 4460 : 2022 : REV A Standard Practice for Calculating Precision Limits Where Values Are Calculated from Other Test Methods
    ASTM D 6607 : 2021 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits
    ASTM D 7227/D7227M : 2022 Standard Practice for Rapid Drying of Compacted Asphalt Mixture Specimens Using Vacuum Drying Apparatus
    ASTM D 979/D979M : 2022 Standard Practice for Sampling Asphalt Mixtures
    ASTM D 4867/D4867M : 2022 Standard Test Method for Effect of Moisture on Asphalt Mixtures
    ASTM D 3203 : 2022 Standard Test Method for Percent Air Voids in Compacted Asphalt Mixtures
    ASTM D 2950/D2950M : 2022 Standard Test Method for Density of Asphalt Mixtures in Place by Nuclear Methods
    ASTM D 8259/D8259M : 2021 Standard Test Method for Rotary Wheel Testing (RWT) of Compacted Asphalt Mixtures
    ASTM D 8237 : 2021 Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures with the Four-Point Beam Fatigue Device
    ASTM D 1188/D1188M : 2022 Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Coated Samples
    ASTM D 6995 : 2021 Standard Test Method for Determining Field VMA Based on the Maximum Specific Gravity of an Asphalt Mixture (Gmm)
    ASTM D 8237 : 2018 Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures With the Four-Point Beam Fatigue Device
    ASTM D 7870/D7870M : 2020 Standard Practice for Moisture Conditioning Compacted Asphalt Mixture Specimens by Using Hydrostatic Pore Pressure
    ASTM D 7981 : 2020 Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor
    ASTM D 7115 : 2020 Standard Test Method for Measurement of Superpave Gyratory Compactor (SGC) Internal Angle of Gyration Using Simulated Loading
    ASTM D 8044 : 2016 Standard Test Method for Evaluation of Asphalt Mixture Cracking Resistance using the Semi-Circular Bend Test (SCB) at Intermediate Temperatures

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 563 : 1997 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
    ASTM D 3666 : 2013 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2011 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 4753 : 2002 Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
    ASTM D 4753 : 2015 Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
    ASTM D 3666 : 2007 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM E 2251 : 2007 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM E 2251 : 2003 : REV A Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 1188 : 2007 : EDT 1 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples
    ASTM D 3666 : 2009 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM E 2251 : 2003 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 1188 : 2007 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples
    ASTM D 1188 : 2007 : R2015 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples
    ASTM E 2251 : 2010 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 4753 : 1995 Standard Specification for Evaluating, Selecting, and Specifying Balances and Scales for Use in Soil, Rock, and Construction Materials Testing
    ASTM D 3666 : 2005 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2003 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM E 2251 : 2011 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM E 2251 : 2014 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 1188 : 1996 : R2002 : EDT 1 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens
    ASTM D 3666 : 2000 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2007 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2007 : EDT 2 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 4753 : 2007 Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
    ASTM D 1188 : 1996 : R2002 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens
    ASTM D 3666 : 2016 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2003 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 1188 : 1996 : EDT 1 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens
    ASTM D 3666 : 2001 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2006 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2004 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM E 77 : 1998 Standard Test Method for Inspection and Verification of Thermometers
    ASTM D 3666 : 2005 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2007 : REV A : EDT 1 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2009 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    ASTM D 3666 : 2002 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective