ASTM D 2734 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Void Content of Reinforced Plastics
20-11-2023
English
07-09-2016
CONTAINED IN VOL. 08.02, 2016 Outlines the void content of reinforced plastics or 'composites.' Applies to composites for which the effects of ignition on the materials are known.
Committee |
D 20
|
DocumentType |
Redline
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1These test methods cover the void content of reinforced plastics or “composites.” The test methods are applicable to composites for which the effects of ignition on the materials are known. Most plastics, glass, and reinforcements fall into this class. These test methods are not applicable to composites for which the effects of ignition on the plastics, the reinforcement, and any fillers are unknown. This class may include silicone resins, which do not burn off completely, reinforcements consisting of metals, organic materials, or inorganic materials which may gain or lose weight, and fillers consisting of oxides, carbonates, etc., which may gain or lose weight. Note that separate weight loss tests of individual materials will usually, but not necessarily, give the same result as when all the materials are combined.
Note 1:There is no known ISO equivalent to these test methods.
1.2The values stated in SI units are to be regarded as standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
CSA S807 : 2010 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
ASTM D 6416/D6416M : 2016 : REDLINE | Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load |
SAE AMS3847D | CLOTH, QUARTZ, 'B' STAGE POLYIMIDE RESIN IMPREGNATED, STYLE 581 FABRIC, 315 DEGREES C (599 DEGREES F) |
ASTM D 3039/D3039M : 2017 : REDLINE | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
ASTM D 5687/D5687M : 1995 : R2015 | Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation |
ASTM D 3410/D3410M : 2016 : REDLINE | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading |
ASTM D 7248/D7248M : 2012 : R2017 | Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens |
ASTM F 602 : 2009 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
ASTM F 602 : 2009 : R2015 | Standard Criteria for Implantable Thermoset Epoxy Plastics (Withdrawn 2024) |
ASTM D 2344/D2344M : 2016 : REDLINE | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates |
ASTM D 6115 : 1997 | Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 5379/D5379M : 2012 : REDLINE | Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method |
ASTM D 5687/D5687M : 1995 : R2002 | Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation |
ASTM D 5528 : 2013 : REDLINE | Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 7905/D7905M : 2014 | Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM E 1556 : 2012 : REDLINE | Standard Specification for Epoxy Resin System for Composite Skin, Honeycomb Sandwich Panel Repair |
ASTM D 7078/D7078M : 2012 : REDLINE | Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method |
CSA S808 : 2014 | SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES |
CSA S807 : 2010 : R2015 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
ASTM D 5467/D5467M : 1997 : R2010 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam |
SAE AMS3845C | CLOTH, TYPE 'E' GLASS, 'B' STAGE ADDITION CURE POLYIMIDE-RESIN-IMPREGNATED |
ASTM D 5229/D5229M : 2014-06 | TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS |
ASTM D 6264 : 1998 | Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force |
ASTM C 364/C364M : 2016 : REDLINE | Standard Test Method for Edgewise Compressive Strength of Sandwich Constructions |
ASTM D 6115 : 1997 : R2004 | Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
ASTM D 5450/D5450M : 2016 : REDLINE | Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders |
ASTM F 641 : 2009 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
SAE AMS3906C | GLASS TAPE AND FLAT SHEET, NON-WOVEN CLOTH EPOXY RESIN IMPREGNATED, FOR HAND AND MACHINE LAYUP |
MIL-PRF-46190 Revision A:1997 | PREPEGS, WOVEN FABRIC, CARBON FIBER, RESIN IMPREGNATED |
SAE AMS 3897 : 2016 | CLOTH, CARBON FIBER, RESIN IMPREGNATED |
SAE AMS 3844 : 2016 | Cloth, Type "E" Glass, Style 7781 Fabric Hot-Melt, Addition-Type, Polyimide Resin Impregnated |
SAE AMS 3960 : 2015 | Advanced Composites Prepreg - Nominal 250 °F Cure - Carbon Fiber and Epoxy Resin, Unidirectional Tape |
ASTM F 602 : 2009 : R2014 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
ASTM D 6115 : 1997 : R2011 | Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites |
CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
ASTM D 6484/D6484M : 2014 : REDLINE | Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates |
SAE AMS 3903 : 2013 | CLOTH, ORGANIC FIBER (PARA-ARAMID), HIGH MODULUS, EPOXY RESIN IMPREGNATED |
SAE AMS 3912 : 2014 | RADOMES, FOAM SANDWICH, POLYIMIDE/QUARTZ CLOTH CONSTRUCTION |
ASTM D 5467/D5467M : 1997 : R2004 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam |
ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
ASTM D 5467/D5467M : 1997 : R2017 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using a Sandwich Beam |
SAE AMS 3849 : 2016 | CLOTH, QUARTZ, STYLE 581 FABRIC - HOT MELT, ADDITION TYPE, POLYIMIDE RESIN IMPREGNATED |
ASTM D 7248/D7248M : 2012 | Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens |
ASTM C 297/C297M : 2016 : REDLINE | Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions |
SAE AMS3894F | Carbon Fiber Tape and Sheet Epoxy Resin Impregnated |
ASTM D 5687/D5687M :1995 | Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation |
SAE AMS 3915 : 2015 | ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - GLASS FIBER AND EPOXY RESIN, 7781 WEAVE FABRIC |
ASTM D 5449/D5449M : 2016 : REDLINE | Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders |
SAE AMS 3913 : 2014 | RADOME, FOAM SANDWICH, HOT-MELT, ADDITION-TYPE POLYIMIDE |
SAE AMS 3829 : 2016 | CLOTH, TYPE 'E' GLASS, STYLE 7781 FABRIC, SOLUTION-ADDITION-TYPE PMR 15 POLYIMIDE RESIN IMPREGNATED |
SAE AMS 3914A : 2015 | ADVANCED COMPOSITES PREPREG - NOMINAL 250 DEGREES F CURE - 12K TOW CARBON FIBER AND EPOXY RESIN, PLAIN WEAVE FABRIC |
ASTM D 5961/D5961M : 2017 : REDLINE | Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates |
ASTM D 5448/D5448M : 2016 : REDLINE | Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders |
ASTM D 5687/D5687M : 1995 : R2007 | Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation |
ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.