![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 2855 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
Hardcopy , PDF
27-08-2020
English
01-11-2015
Committee |
F 17
|
DocumentType |
Standard Practice
|
Pages |
10
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This practice describes a two-step (primer and solvent cement) method of joining poly(vinyl chloride) (PVC) or chlorinated poly(vinyl chloride) (CPVC) pipe and piping components with tapered sockets.
Note 1:Simplified procedures may be allowed in non-pressure applications where local codes permit.
Note 2:Where conflicts occur between the code and the manufacturer’s installation instructions, the more restrictive provisions apply.
1.2The products covered by this practice are intended for use with the distribution of pressured liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.
Note 3:Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason.
1.3This standard practice does not address the one-step method of joining pipe and piping components with tapered sockets with solvent cement without the use of primer.
1.4The techniques covered are applicable to joining PVC to PVC or CPVC to CPVC pipe and piping components with tapered sockets. In the remainder of this standard practice, the term “piping components with tapered sockets”, whether it be bell end pipe, spigot connections, or any other type of tapered connections, will be referred to as “fittings.”
1.5A partial list of standards for PVC and CPVC pipe, piping components, and solvent cements suitable for use in joining pipe and fittings is given in Appendix X1.
1.6The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7The text of this practice references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.
1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM F 891 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
ASTM F 679 : 2016 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
ASTM F 1668 : 2016 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
ASTM F 3097 : 2015 | Standard Practice for Installation of an Outside Sewer Service Cleanout through a Minimally Invasive Small Bore Vacuum Excavation |
ASTM D 3034 : 2016 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
ASTM D 2672 : 2014 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
ASTM F 512 : 2012 : R2017 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
ASTM F 1866 : 2018 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM F 1488 : 2014 : R2019 | Standard Specification for Coextruded Composite Pipe |
ASTM F 1760 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
ASTM F 480 : 2014 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
ASTM F 949 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
ASTM F 2387 : 2004 : R2012 | Standard Specification for Manufactured Safety Vacuum Release Systems (SVRS) for Swimming Pools, Spas and Hot Tubs |
ASTM F 656 : 2015 | Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) Plastic Pipe and Fittings |
ASTM F 3128 : 2019 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
ASTM F 2658 : 2007 : R2019 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
ASTM F 1483 : 2017 | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
ASTM F 794 : 2003 : R2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
ASTM F 758 : 2014 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
ASTM D 1785 : 2015 : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2466 : 2001 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2467 : 2013 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2467 : 2002 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2466 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 3034 : 2006 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2665 : 2007 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2241 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 2949 : 2010 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1785 : 2003 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 2564 : 2004 : R2009 : EDT 1 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2564 : 2004 : EDT 1 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2564 : 2012 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2949 : 2000 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1785 : 2004 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 2466 : 2002 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2665 : 2004 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2008 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2467 : 2004 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 1784 : 1999 : REV A : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2665 : 2004 : REV A : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2466 : 2006 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2949 : 2001 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 1978 | Standard Specification for Poly(inyl Chloride) (PVC) Plastic Drain, Waste, And Vent Pipe And Fittings |
ASTM D 2467 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 1784 : 2003 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2729 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2949 : 2001 : REV A | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2672 : 1996 : REV A | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
ASTM D 2729 : 2011 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 1785 : 2005 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM F 1866 : 2005 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 2665 : 1991 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 3034 : 2014 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1784 : 2011 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 3034 : 2004 : REV A | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2949 : 2001 : REV A : EDT 1 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2949 : 2001 : REV A : R2008 : EDT 1 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2467 : 2006 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2467 : 2004 : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2241 : 2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM D 2466 : 2013 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2467 : 2013 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2665 : 2008 : REV B | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1785 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 1784 : 2008 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
ASTM F 1866 : 2018 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 2241 : 2004 : REV B | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 2466 : 2005 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2949 : 1978 | Standard Specification for 3.25- In. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, And Vent Pipe And Fittings |
ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2729 : 2003 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM F 1866 : 1998 | Standard Specification for Poly (Vinyl Chloride ) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 2467 : 2005 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 2665 : 2002 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2004 : REV A : EDT 2 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2672 : 2014 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
ASTM D 2241 : 2005 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM F 1866 : 2013 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 3034 : 2015 : EDT 1 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2241 : 2004 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 2665 : 2012 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2564 : 1991 | Standard Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 1784 : 2006 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2241 : 2004 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
ASTM D 1785 : 2004 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 2949 : 1978 | Standard Specification for 3.25- In. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, And Vent Pipe And Fittings |
ASTM D 1784 : 2007 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 1785 : 2012 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 2949 : 2010 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2002 : REV A : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2466 : 1999 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 1785 : 2006 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 3034 : 2008 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 3034 : 2014 : REV A | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2665 : 2004 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2008 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2564 : 2002 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM F 1866 : 2007 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 1784 : 2020 | Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2466 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 |
ASTM D 2564 : 1991 : REV A | Standard Specification for Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2564 : 2004 | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2949 : 2000 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2729 : 1978 : EDT 1 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe And Fittings |
ASTM D 2672 : 1996 : REV A : R2003 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
ASTM D 3034 : 2016 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2665 : 2000 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM F 1866 : 2013 : R2017 | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
ASTM D 2665 : 2001 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 1784 : 2002 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2467 : 1999 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 1785 : 1999 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
ASTM D 2949 : 2001 : REV A : R2008 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2672 : 1996 : REV A : R2009 | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
ASTM D 2564 : 1996 : REV A | Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems |
ASTM D 2241 : 2000 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D 2467 : 2001 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 |
ASTM D 1784 : 2006 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D 2665 : 2002 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 3034 : 2004 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2665 : 2010 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 2665 : 2011 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
ASTM D 3034 : 2000 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 2729 : 1996 : REV A | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
ASTM D 3034 : 2015 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.