• Shopping Cart
    There are no items in your cart

ASTM D 2914 : 2015 : R2022

Current

Current

The latest, up-to-date edition.

Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-03-2022

€61.92
Excluding VAT

Committee
D 22
DocumentType
Test Method
Pages
15
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

1.1These test methods cover the bubbler collection and colorimetric determination of sulfur dioxide (SO2) in the ambient or workplace atmosphere.

1.2These test methods are applicable for determining SO2 over the range from approximately 25 μg/m3 (0.01 ppm(v)) to 1000 μg/m3 (0.4 ppm(v)), corresponding to a solution concentration of 0.03 μg SO2/mL to 1.3 μg SO2/mL. Beer's law is followed through the working analytical range from 0.02 μg SO2/mL to 1.4 μg SO2/mL.

1.3The lower limit of detection is 0.075 μg SO2/mL (1),2 representing an air concentration of 25 μg SO2/m3 (0.01 ppm(v)) in a 30-min sample, or 13 μg SO2/m3 (0.005 ppm(v)) in a 24-h sample.

1.4These test methods incorporate sampling for periods between 30 min and 24 h.

1.5These test methods describe the determination of the collected (impinged) samples. A Method A and a Method B are described.

1.6Method A is preferred over Method B, as it gives the higher sensitivity, but it has a higher blank. Manual Method B is pH-dependent, but is more suitable with spectrometers having a spectral band width greater than 20 nm.

Note 1:These test methods are applicable at concentrations below 25 μg/m3 by sampling larger volumes of air if the absorption efficiency of the particular system is first determined, as described in Annex A4.

Note 2:Concentrations higher than 1000 μg/m3 can be determined by using smaller gas volumes, larger collection volumes, or by suitable dilution of the collected sample with absorbing solution prior to analysis.

1.7The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.8Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

1.9This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 8.3.1, Section 9, and A3.1.3.

1.10This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM B 827 : 2005 : R2020 Standard Practice for Conducting Mixed Flowing Gas (MFG) Environmental Tests
ASTM D 2913 : 2020 Standard Test Method for Mercaptan Content of the Atmosphere

ASTM D 1914 : 1995 : R2022 Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres
ASTM D 3609 : 2000 : R2014 Standard Practice for Calibration Techniques Using Permeation Tubes
ASTM D 3609 : 2022 Standard Practice for Calibration Techniques Using Permeation Tubes
ASTM E 1 : 2014 : R2020 Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM D 1914 : 1995 : R2014 Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.