ASTM D 2915 : 2017 : R2022
Current
The latest, up-to-date edition.
Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products
Hardcopy , PDF
English
08-03-2022
Committee |
D 07
|
DocumentType |
Standard Practice
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This practice covers sampling and analysis procedures for the investigation of specified populations of wood and wood-based structural products referred to in this standard as products. Appropriate product standards should be referenced for presentation requirements for data. Depending on the interest of the user, the population from which samples are taken may range from the products produced at a specific manufacturing site to all the products produced in a particular grade from a particular geographic area, during some specified interval of time. This practice generally assumes that the population is sufficiently large so that, for sampling purposes, it may be considered infinite. Where this assumption is inadequate, that is, the population is assumed finite, many of the provisions of this practice may be employed but the sampling and analysis procedure must be designed to reflect a finite population. The statistical techniques embodied in this practice provide procedures to summarize data so that logical judgments can be made. This practice does not specify the action to be taken after the results have been analyzed. The action to be taken depends on the particular requirements of the user of the product.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This practice does not purport to address the adjustment factors needed to adjust test data to standardized mechanical and environmental conditions (that is, temperature, moisture, test span, or load duration). Additionally, it provides a basis for statistical estimates that will typically require further adjustment to determine design values for use with an accepted design methodology (that is, allowable stress, limit states, or load and resistance factor design). It shall be the responsibility of the user to seek out the appropriate adjustments in specific product standards.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6570 : 2018 : REV A | Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber |
ASTM D 7341 : 2021 | Standard Practice for Establishing Characteristic Values for Flexural Properties of Structural Glued Laminated Timber by Full-Scale Testing |
ASTM D 2555 : 2017 : REV A | Standard Practice for Establishing Clear Wood Strength Values |
ASTM D 7469 : 2021 | Standard Test Methods for End Joints in Structural Wood Products |
ASTM D 8391 : 2022 | Standard Specification for Demonstrating Equivalent Fire Performance for Wood-Based Floor Framing Members to Unprotected 2 by 10 Dimension Lumber or Equal-Sized Structural Composite Lumber |
ASTM D 7258 : 2017 | Standard Specification for Polymeric Piles |
ASTM D 7199 : 2020 | Standard Practice for Establishing Characteristic Values for Reinforced Glued Laminated Timber (Glulam) Beams Using Mechanics-Based Models |
ASTM D 5652 : 2021 | Standard Test Methods for Single-Bolt Connections in Wood and Wood-Based Products |
ASTM D 7672 : 2019 | Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies |
ASTM D 5457 : 2021 : REV A | Standard Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design |
ASTM D 198 : 2021 : REV A | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
ASTM D 7381 : 2007 : R2021 : EDT 1 | Standard Practice for Establishing Allowable Stresses for Round Timbers for Piles from Tests of Full-Size Material |
ASTM D 7247 : 2017 | Standard Test Method for Evaluating the Shear Strength of Adhesive Bonds in Laminated Wood Products at Elevated Temperatures |
ASTM D 5764 : 1997 : REV A : R2018 | Standard Test Method for Evaluating Dowel-Bearing Strength of Wood and Wood-Based Products |
ASTM D 6815 : 2009 : R2015 | Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products |
ASTM D 6555 : 2017 | Standard Guide for Evaluating System Effects in Repetitive-Member Wood Assemblies |
ASTM E 2954 : 2015 | Standard Test Method for Axial Compression Test of Reinforced Plastic and Polymer Matrix Composite Vertical Members |
ASTM D 5456 : 2021 : EDT 1 | Standard Specification for Evaluation of Structural Composite Lumber Products |
ASTM D 7568 : 2017 | Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications |
ASTM D 3737 : 2018 : EDT 1 | Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam) |
ASTM D 7032 : 2021 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 5516 : 2018 | Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures |
ASTM D 6782 : 2019 | Standard Test Methods for Standardization and Calibration of In-Line Dry Lumber Moisture Meters |
ASTM D 4761 : 2019 | Standard Test Methods for Mechanical Properties of Lumber and Wood-Based Structural Materials |
ASTM D 1037 : 2012 : R2020 | Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials |
ASTM D 7031 : 2011 : R2019 | Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products |
ASTM D 7438 : 2020 | Standard Practice for Field Calibration and Application of Hand-Held Moisture Meters |
ASTM D 5055 : 2019 : EDT 1 | Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists |
ASTM D 1990 : 2019 | Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens |
ASTM D 1761 : 2020 | Standard Test Methods for Mechanical Fasteners in Wood and Wood-Based Materials |
ASTM D 4444 : 2013 : R2018 | Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters |
ASTM D 6662 : 2017 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 7857 : 2016 | Standard Test Method for Evaluating the Flexural Properties and Internal Bond Strength of Fire-Retarded Mat-Formed Wood Structural Composite Panels Exposed to Elevated Temperatures |
ASTM D 6109 : 2019 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber and Related Products |
ASTM D 7033 : 2022 | Standard Practice for Establishing Design Capacities for Oriented Strand Board (OSB) Wood-Based Structural-Use Panels |
ASTM D 5574 : 1994 : R2021 | Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints |
ASTM D 6874 : 2021 | Standard Test Methods for Nondestructive Evaluation of the Stiffness of Wood and Wood-Based Materials Using Transverse Vibration or Stress Wave Propagation |
ASTM D 3737 : 2018 : R2023 : EDT 1 | Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam) |
ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM D 245 : 2022 | Standard Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber |
ASTM D 2555 : 2017 : REV A : R2024 : EDT 1 | Standard Practice for Establishing Clear Wood Strength Values |
ASTM D 6570 : 2018 : REV A : R2023 : EDT 1 | Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber |
ASTM D 1990 : 2024 | Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens |
ASTM D 2555 : 2017 : REV A : R2024 | Standard Practice for Establishing Clear Wood Strength Values |
ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.