ASTM D 2990 : 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
Hardcopy , PDF
11-11-2014
English
01-09-2009
Committee |
D 20
|
DocumentType |
Test Method
|
Pages |
20
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 These test methods cover the determination of tensile and compressive creep and creep-rupture of plastics under specified environmental conditions (see 3.1.3).
1.2 While these test methods outline the use of three-point loading for measurement of creep in flexure, four-point loading (which is used less frequently) can also be used with the equipment and principles as outlined in Test Methods D 790
1.3 For measurements of creep-rupture, tension is the preferred stress mode because for some ductile plastics rupture does not occur in flexure or compression.
1.4 Test data obtained by these test methods are relevant and appropriate for use in engineering design.
1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 6.8.2.
Note 1—This standard and ISO 899 Parts 1 and 2 address the same subject matter, but differ in technical content (and results cannot be directly compared between the two test methods). ISO 899 Part 1 addresses tensile creep and creep to rupture and ISO 899 Part 2 addresses flexural creep. Compressive creep is not addressed in ISO 899.
ASTM F 2902 : 2016 : EDT 1 | Standard Guide for Assessment of Absorbable Polymeric Implants |
ASTM F 2150 : 2013 | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products |
ASTM D 5262 : 2007 : R2016 | Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics |
ASTM F 624 : 2009 : R2015 : EDT 1 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
ASTM D 7361 : 2007 : R2018 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM F 561 : 2019 | Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids |
ASTM F 2881/F2881M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
ASTM D 5819 : 2018 | Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability |
ASTM F 2789 : 2010 : R2015 | Standard Guide for Mechanical and Functional Characterization of Nucleus Devices |
ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
ASTM D 907 : 2015 | Standard Terminology of Adhesives |
ASTM D 6112 : 2018 | Standard Test Methods for Compressive and Flexural Creep and Creep-Rupture of Plastic Lumber and Shapes |
ASTM F 2787 : 2013 : R2018 | Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers |
ASTM F 2947/F2947M : 2019 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
ASTM D 7931 : 2018 | Standard Guide for Specifying Drainage Geocomposites |
ASTM D 4762 : 2018 | Standard Guide for Testing Polymer Matrix Composite Materials |
ASTM D 7406 : 2007 : R2012 | Standard Test Method for Time-Dependent (Creep) Deformation Under Constant Pressure for Geosynthetic Drainage Products |
ASTM D 6992 : 2016 | Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM F 2922 : 2013 : R2018 | Standard Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers |
ASTM F 2418 : 2016 : REV A | Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers |
ASTM F 2903 : 2011 | Standard Guide for Tissue Engineered Medical Products (TEMPs) for Reinforcement of Tendon and Ligament Surgical Repair (Withdrawn 2020) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.