ASTM D 3222 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
Hardcopy , PDF
11-11-2014
English
01-07-2005
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.02, 2018 Gives melt processable molding and extrusion materials, and coating materials of poly(vinylidene fluoride) (PVDF) fluoroplastics.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2005
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This specification covers melt processable molding and extrusion materials, as well as coating materials of poly(vinylidene fluoride) fluoroplastic, commonly abbreviated PVDF (or PVF
1.2 This specification applies only to the virgin homopolymer prepared from vinylidene fluoride, not copolymers, reinforced, filled grades or special grades with additives or treatments for modification of attributes.
1.3 The tests involved are intended to provide information for specification of unmodified PVDF homopolymer resins. It is not the purpose of this specification to provide engineering data for design purposes.
1.4 PVDF fluoroplastics melt between 156 and 180°C [312 and 356°F] and are thermally stable up to about 370°C [698°F]. (Warning—Evolution of corrosive and toxic hydrogen fluoride can occur under certain conditions.)
1.5 The values stated in SI units, as detailed in IEEE/SI-10, are to be regarded as the standard. The values given in brackets are for information only.
Note 1—PVDF exhibits polymorphism. The type and extent of crystalline structure varies with the thermomechanical history of the sample. Specimens prepared by techniques different than prescribed in this specification can have properties that vary from the values specified.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 10.
Note 2—There is no equivalent ISO standard for this specification. Information in this specification is technically equivalent to related information in ISO 12086-1 and ISO 12086-2.
| ASTM D 5575 : 2018 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM F 1545 : 2015 : REV A | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
| ASTM F 1986 : 2001 : R2011 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems (Withdrawn 2020) |
| ASTM F 1673 : 2010 : R2016 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6713 : 2014 | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
| ASTM F 1987 : 2001 : R2011 | Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems (Withdrawn 2020) |
| ASTM D 4967 : 1999 : R2013 | Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables |
| ASTM D 3418 : 2015 : REDLINE | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ISO 12086-1:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ISO 12086-2:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 3835 : 2016 : REDLINE | Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D 257 : 2014 : REDLINE | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D 542 : 2014 : REDLINE | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.