• Shopping Cart
    There are no items in your cart

ASTM D 3294 : 2015 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes

Available format(s)

PDF

Superseded date

25-07-2022

Language(s)

English

Published date

10-09-2015

€67.30
Excluding VAT

CONTAINED IN VOL. 08.02, 2015 Defines requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of 0.794 mm (1/32 in.) manufactured from PTFE resin molding materials.

Committee
D 20
DevelopmentNote
Supersedes ASTM D 3293 (12/2001)
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of 0.794 mm (1/32in.) manufactured from PTFE resin molding materials defined in Specification D4894.

1.2This specification also establishes requirements for molded basic shapes made from molding materials. This specification is for products 300 mm (12 in.) or less in a dimension parallel to and 12.7 mm (0.5 in.) or greater in the dimension perpendicular to the direction of the applied molding pressure.

1.3The values stated in SI units are to be regarded as the standard.

1.4The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Special attention is called to 13.2, 13.3, 13.6, 13.8, and A1.

Note 1:There is no known ISO equivalent to this standard.

ASTM F 1511 : 2016-11 SPECIFICATION FOR MECHANICAL SEALS FOR SHIPBOARD PUMP APPLICATIONS
ASTM F 754 : 2008 Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
ASTM F 336 : 2002 : R2009 Standard Practice for Design and Construction of Nonmetallic Enveloped Gaskets for Corrosive Service
04/30091874 DC : DRAFT FEB 2004 BS EN ISO 13000-1 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION
ASTM F 336 : 2002 : R2016 Standard Practice for Design and Construction of Nonmetallic Enveloped Gaskets for Corrosive Service
EN ISO 13000-1:2005 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)
ASTM F 754 : 2008 : R2015 Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
I.S. EN ISO 13000-2:2006 PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN ISO 13000-1:2006 PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION
04/30091878 DC : DRAFT FEB 2004 BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN ISO 13000-1:2005 Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Requirements and designation
ISO 13000-1:2005 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation
NASA STD 6001 : 2011 FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES
ASTM F 336 : 2002 Standard Practice for Design and Construction of Nonmetallic Enveloped Gaskets for Corrosive Service
BS EN ISO 13000-2:2005 Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Preparation of test specimens and determination of properties
ISO 13000-2:2005 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties
EN ISO 13000-2:2005 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)
DIN EN ISO 13000-2:2006-02 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)
DIN EN ISO 13000-1:2006-02 Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)
ASME RTP 1 : 2015 REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT
ASME RTP-1 : 2017 REINFORCED THERMOSET PLASTIC CORROSION-RESISTANT EQUIPMENT

ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ASTM D 374 : 1999 Standard Test Methods for Thickness of Solid Electrical Insulation
ASTM D 3892 : 2015 : REDLINE PRACTICE FOR PACKAGING/PACKING OF PLASTICS

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.