ASTM D 3295 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing
09-01-2021
English
01-09-2015
CONTAINED IN VOL. 08.02, 2015 Explains PTFE tubing, miniature beading and spiral cut tubing-manufactured from PTFE resin produced from dispersion specified in Specification D 4895.
Committee |
D 20
|
DocumentType |
Redline
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers PTFE tubing, miniature beading and spiral cut tubing-manufactured from PTFE resin produced from dispersion specified in Specification D4895.
Note 1:PTFE tube and rod manufactured from resin specified in Specification D4894 are covered in Specification D1710.
1.2The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only.
1.3The following hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4As PTFE resin produced from dispersion is not a true thermoplastic material, any reuse for the specification referenced above is impossible. However, markets do exist for non-virgin PTFE as additives and fillers.
Note 2:There is no known ISO equivalent to this standard.
DOD-STD-2000-1 Revision B:1986 | SOLDERING TECHNOLOGY, HIGH QUALITY/HIGH RELIABILITY |
MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
EN ISO 13000-1:2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005) |
I.S. EN ISO 13000-2:2006 | PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
I.S. EN ISO 13000-1:2006 | PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION |
04/30091878 DC : DRAFT FEB 2004 | BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
BS EN ISO 13000-1:2005 | Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Requirements and designation |
ISO 13000-1:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation |
MIL-HDBK-454 Revision B:2007 | GENERAL GUIDELINES FOR ELECTRONIC EQUIPMENT |
04/30091874 DC : DRAFT FEB 2004 | BS EN ISO 13000-1 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION |
BS EN ISO 13000-2:2005 | Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Preparation of test specimens and determination of properties |
ISO 13000-2:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 2: Preparation of test specimens and determination of properties |
EN ISO 13000-2:2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
DIN EN ISO 13000-2:2006-02 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
DIN EN ISO 13000-1:2006-02 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005) |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM D 1710 : 2015 : REDLINE | Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.