ASTM D 3306 : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
Hardcopy , PDF
06-01-2022
English
04-06-2020
Committee |
D 15
|
DocumentType |
Standard
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the requirements for ethylene glycol or propylene glycol base engine coolants used in automobiles or other light duty service cooling systems. When concentrates are used at 40 to 70 % concentration by volume in water, or when prediluted glycol base engine coolants 50 volume % or higher engine coolant concentrate are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion.
1.2The coolants governed by this specification are categorized as follows:
Coolant Type | Description |
I | Ethylene glycol base concentrate |
II | Propylene glycol base concentrate |
V | Ethylene glycol base concentrate |
III | Ethylene glycol predilute 50 volume % or higher engine coolant concentrate |
IV | Propylene glycol predilute 50 volume % or higher engine coolant concentrate |
VI | Ethylene glycol base predilute |
Note 1:This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. This specification shall also apply to engine coolants prepared using glycol generated from recycled or reprocessed used coolant or reprocessed industrial-source glycol, provided that said glycol meets the requirements of Specification E1177. Separate specifications (D6471 and D6472) exist for engine coolants prepared from recycled or reprocessed used coolant or reprocessed industrial-source glycol that does not meet the requirements established in Specification E1177. This specification shall also apply to glycol based engine coolants prepared using fully refined glycerin provided that said glycerin meets the requirements for Specification D7640.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2:This specification applies to glycol base engine coolant for automobiles and light duty service. Specifications D4985 and D6210 exist for heavy duty engine service.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 2847 : 2015 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
ASTM D 4725 : 2015 | Standard Terminology for Engine Coolants and Related Fluids |
ASTM D 7715 : 2012 : R2021 | Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines |
ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
ASTM D 7640 : 2016 : R2021 | Standard Specification for Engine Coolant Grade Glycerin |
ASTM D 512 : 2012 | Standard Test Methods for Chloride Ion In Water (Withdrawn 2021) |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM D 1123 : 1999 | Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
ASTM D 1882 : 2017 : R2021 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
ASTM D 1882 : 2017 | Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles |
ASTM D 7640 : 2016 | Standard Specification for Engine Coolant Grade Glycerin |
ASTM E 1177 : 1998 | Standard Specification for Engine Coolant Grade Ethylene Glycol |
ASTM E 394 : 2000 | Standard Test Method for Iron in Trace Quantities Using the 1,10-Phenanthroline Method |
ASTM D 1126 : 1996 | Standard Test Method for Hardness in Water |
ASTM D 5931 : 2013 : R2017 | Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.