ASTM D 3410/D3410M : 2016 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
English
29-03-2016
CONTAINED IN VOL. 15.03, 2016 Specifies the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
Committee |
D 30
|
DevelopmentNote |
Supersedes ASTM D 3410. (12/2008)
|
DocumentType |
Redline
|
Pages |
19
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
1.1This test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. The composite material forms are limited to continuous-fiber or discontinuous-fiber reinforced composites for which the elastic properties are specially orthotropic with respect to the test direction. This test procedure introduces the compressive force into the specimen through shear at wedge grip interfaces. This type of force transfer differs from the procedure in Test Method D695 where compressive force is transmitted into the specimen by end-loading, Test Method D6641/D6641M where compressive force is transmitted by combined shear and end loading, and Test Method D5467/D5467M where compressive force is transmitted by subjecting a honeycomb core sandwich beam with thin skins to four-point bending.
1.2This test method is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pounds units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
Note 1:Additional procedures for determining compressive properties of resin-matrix composites may be found in Test Methods D695, D5467/D5467M, and D6641/D6641M.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 6641 : 2001 | TEST METHOD FOR DETERMINING THE COMPRESSIVE PROPERTIES OF POLYMER MATRIX COMPOSITE LAMINATES USING A COMBINED LOADING COMPRESSION (CLC) TEST FIXTURE |
CSA S807 : 2010 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
ASTM E 1434 : 2000 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM D 8066/D8066M : 2017 | Standard Practice Unnotched Compression Testing of Polymer Matrix Composite Laminates |
ASTM D 5467/D5467M : 1997 : R2017 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using a Sandwich Beam |
ASTM D 6856/D6856M : 2003 : R2008 : EDT 1 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM E 1309 : 2000 : R2005 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 6641 : 2001 | TEST METHOD FOR DETERMINING THE COMPRESSIVE PROPERTIES OF POLYMER MATRIX COMPOSITE LAMINATES USING A COMBINED LOADING COMPRESSION (CLC) TEST FIXTURE |
CSA S808 : 2014 | SPECIFICATION FOR FIBRE-REINFORCED POLYMER (FRP) MATERIALS FOR EXTERNALLY REINFORCING STRUCTURES |
CSA S807 : 2010 : R2015 | SPECIFICATION FOR FIBRE-REINFORCED POLYMERS |
ASTM D 5467/D5467M : 1997 : R2010 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam |
MIL-DTL-64154 Revision B:2008 | LAMINATE: FIBERGLASS-FABRIC-REINFORCED, PHENOLIC |
ASTM D 6641 : 2001e1 | TEST METHOD FOR DETERMINING THE COMPRESSIVE PROPERTIES OF POLYMER MATRIX COMPOSITE LAMINATES USING A COMBINED LOADING COMPRESSION (CLC) TEST FIXTURE |
ASTM E 1309 : 2000 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 6856 : 2003 : R2008 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM D 6856/D6856M : 2003 : R2016 | Standard Guide for Testing Fabric-Reinforced “Textile” Composite Materials |
MIL-PRF-46190 Revision A:1997 | PREPEGS, WOVEN FABRIC, CARBON FIBER, RESIN IMPREGNATED |
ASTM E 1434 : 2000 : R2013 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015) |
ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 7332/D7332M : 2016 : REDLINE | Standard Test Method for Measuring the Fastener Pull-Through Resistance of a <brk/>Fiber-Reinforced Polymer Matrix Composite |
CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
I.S. EN ISO 14126:2000 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF COMPRESSIVE PROPERTIES IN THE IN-PLANE DIRECTION |
ASTM D 5467/D5467M : 1997 : R2004 | Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composites Using a Sandwich Beam |
MIL-PRF-46187 Revision A:1998 | PREPREG, UNIDIRECTIONAL TAPE, CARBON (GRAPHITE) FIBER HIGH TEMPERATURE RESIN IMPREGNATED, 316 DEGREES C (600 DEGREES F) |
ASTM E 1434 : 2000 : R2006 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
BS EN ISO 14126:1999 | Fibre-reinforced plastic composites. Determination of compressive properties in the in-plane direction |
ISO 14126:1999 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction |
ACI 440R : 2007 | REPORT ON FIBER-REINFORCED POLYMER (FRP) REINFORCEMENT FOR CONCRETE STRUCTURES |
ASTM D 5961/D5961M : 2017 : REDLINE | Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates |
ASTM D 6856 : 2003 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM E 1309 : 2000 : R2011 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015) |
ANSI Y14.5 : 1973 | DIMENSIONING AND TOLERANCING FOR ENGINEERING DRAWINGS |
ASTM E 122 : 2017 : REDLINE | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 5229/D5229M : 2014-06 | TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
ASTM D 5379/D5379M : 2012 : REDLINE | Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method |
ASTM E 132 : 2017 : REDLINE | Standard Test Method for Poisson’s Ratio at Room Temperature |
ASTM D 2734 : 2016 : REDLINE | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3171 : 2015 : REDLINE | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 111 : 2017 : REDLINE | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus |
ASTM D 695 : 2015 : REDLINE | Standard Test Method for Compressive Properties of Rigid Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.