ASTM D 3462/D3462M : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
Hardcopy , PDF
09-06-2023
English
12-03-2019
This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules.
Committee |
D 08
|
DocumentType |
Standard
|
Pages |
4
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification.
1.2Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.].
1.3The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7158/D7158M : 2020 | Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method) |
ASTM D 6381/D6381M : 2015 : R2020 | Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance |
ASTM D 7349/D7349M : 2015 : R2019 | Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners |
ASTM D 1079 : 2018 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1922 : 2008 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM F 1667 : 2005 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
ASTM D 228/D228M : 2021 | Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing |
ASTM F 1667 : 2018 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2015 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2020 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1922 : 2023 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM F 1667 : 2013 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2006 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM F 1667 : 2011 : REV A | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2011 : REV A : EDT 1 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2015 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2021 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2010 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2018 : REV A | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM D 36/D36M : 2014 : EDT 1 | Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) |
ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1922 : 2003 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM F 1667 : 2000 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2003 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2020 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM F 1667 : 2001 : REV A | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM F 1667 : 2011 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2015 : R2020 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM F 1667 : 2002 : REV A | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2003 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM F 1667 : 2017 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2005 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 1922 : 2000 : REV A | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM F 1667 : 2002 | Standard Specification for Driven Fasteners: Nails, Spikes, and Staples |
ASTM D 1922 : 2006 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1922 : 2009 | Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method |
ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.