ASTM D 3641 : 2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
Hardcopy , PDF
11-11-2014
English
10-04-2002
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1 This practice covers the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials. This practice is to be used to obtain uniformity in methods of describing the various steps of the injection molding process and to set up uniform methods of reporting these conditions. The exact conditions required to prepare suitable specimens will vary for each plastic material. Those conditions should become a part of the specification for the material, or be agreed upon between the purchaser and the supplier. Any requirements or recommendations in the material specification which differ from this standard take precedence over those in this standard.
1.2 The methodology presented assumes the use of reciprocating screw injection molding machines.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—This practice is equivalent to the following parts of ISO 294: Plastics-Injection Moulding of Test Specimens of Thermoplastic Materials; 294-1: Part 1-General Principles and Multipurpose Test Specimens (ISO Type A Mould) and Bars (ISO Type B Mould); ISO 294-2: Part 2-Small Tensile Bars (ISO Type C Mould); ISO 294-3: Part 3-Plates (ISO Type D Moulds).
| ASTM F 2617 : 2015 | Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry |
| ASTM D 4203 : 2017 | Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials |
| ASTM D 3419 : 2012 : R2019 | Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds |
| ASTM D 4067 : 2016 | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM D 3965 : 2016 | Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4673 : 2016 | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| ASTM D 706 : 2015 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 6339 : 2011 : R2019 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM D 955 : 2008 : R2014 | Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics |
| ASTM D 5336 : 2015 : REV A | Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material |
| ASTM D 3012 : 2019 | Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven |
| ASTM D 4634 : 2016 | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 788 : 2016 | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 6835 : 2017 | Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) |
| ASTM D 256 : 2010 : R2018 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
| ASTM D 6394 : 2014 | Standard Specification for Sulfone Plastics (SP) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.