ASTM D 3654/D3654M : 2006 : R2024
Current
The latest, up-to-date edition.
Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
Hardcopy , PDF
English
01-10-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 10
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method covers procedures for determining the ability of pressure-sensitive tapes and labels to remain adhered under constant load applied parallel to the surface of the tape and substrate.
1.1.1Procedure A measures the shear adhesion when applied to a vertical standard steel panel.
1.1.2Procedure B measures the shear adhesion when applied to vertical panel covered with NIST SRM 1810A standard fiberboard.
1.1.3Procedure C measures the shear adhesion when applied to a vertical panel covered with a fiberboard as defined by Comite Europeen de Normalisation (CEN).
1.1.4Procedure D measures shear adhesion when applied to a vertical panel covered with a fiberboard agreed upon by the buyer and seller.
1.1.5Procedure E measures shear adhesion of filament reinforced tape when applied to a horizontal standard steel panel.
1.1.6Procedure F measures shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with NIST SRM 1810A standard fiberboard.
1.1.7Procedure G measures the shear adhesion of a filament reinforced tape when applied to a horizontal panel covered with a standard fiberboard defined by CEN.
1.1.8Procedure H measures the shear adhesion the same as Procedure A except the test is conducted at an elevated temperature and after a 10-min dwell time at the elevated temperature.
1.2These procedures provide a means of assessing the uniformity of the adhesive of a given type of pressure-sensitive tape, usually tapes used for packaging applications. The assessment may be within a roll of tape, between rolls or production lots.
1.2.1Variations in the tape backing and adhesive affect the response; therefore, these procedures cannot be used to pinpoint the specific cause(s) of nonuniformity.
1.2.2This test method is intended to replace AFERA 4012, CEN 1943, and PSTC (see 7.2).
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems will result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6463/D6463M : 2006 : R2020 | Standard Test Method for Time to Failure of Pressure Sensitive Articles Under Sustained Shear Loading |
| ASTM D 5486/D5486M : 2006 : R2020 | Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing |
| ASTM D 1974/D1974M : 2022 | Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes |
| ASTM D 5330/D5330M : 2006 : R2020 | Standard Specification for Pressure-Sensitive Tape for Packaging, Filament-Reinforced |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.