ASTM D 3700 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Obtaining LPG Samples Using a Floating Piston Cylinder
04-01-2022
English
14-10-2016
CONTAINED IN VOL. 05.02, 2016 Specifies the equipment and procedures for obtaining a representative sample of specification liquefied petroleum gas (LPG), such as specified in ASTM Specification D 1835, GPA 2140, and comparable international standards.
Committee |
D 02
|
DocumentType |
Redline
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This practice covers the equipment and procedures for obtaining a representative sample of liquefied petroleum gas (LPG), such as specified in ASTM Specification D1835, GPA 2140, and comparable international standards. It may also be used for other natural gas liquid (NGL) products that are normally single phase (for example, NGL mix, field butane, and so forth), defined in other industry specifications or contractual agreements, and for volatile (higher vapor pressure) crude oils.
Note 1:Some floating piston cylinders have such tight piston seals that the vapor pressure of some high vapor pressure crude oils may not be sufficient to allow sampling without a handle to move the piston. An alternative sampling practice for UN Class 3 liquids (under 300 kPa at 52 °C) is Practice D8009, which utilizes a Manual Piston Cylinder (MPC) sampler.
1.2This practice is not intended for non-specification products that contain significant quantities of undissolved gases (N2, CO2), free water or other separated phases, such as raw or unprocessed gas/liquids mixtures and related materials. The same equipment can be used for these purposes, but additional precautions are generally needed to obtain representative samples of multi-phase products (see Appendix X1).
1.3This practice includes recommendations for the location of a sample point in a line or vessel. It is the responsibility of the user to ensure that the sampling point is located so as to obtain a representative sample.
1.4The values stated in SI units are to be regarded as standard.
1.4.1Exception—The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
ASTM D 5799 : 1995 | Standard Test Method for Determination of Peroxides in Butadiene |
ASTM D 5273 : 1992 : R2007 | Standard Guide for Analysis of Propylene Concentrates |
BS 4250-2:1987 | Liquefied petroleum gas. Specification for automotive LPG |
API MPM CH8.1 SPANISH : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
ASTM D 5273 : 1992 : R1997 | Standard Guide for Analysis of Propylene Concentrates |
ASTM D 7901 : 2014 : REV A | Standard Specification for Dimethyl Ether for Fuel Purposes |
ASTM D 7994 : 2017 | Standard Test Method for Total Fluorine, Chlorine, and Sulfur in Liquid Petroleum Gas (LPG) by Oxidative Pyrohydrolytic Combustion Followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC) |
ASTM D 5274 : 2000 : R2005 | Standard Guide for Analysis of 1,3-Butadiene Product |
ASTM D 5274 : 2000 : R2009 | Standard Guide for Analysis of 1,3-Butadiene Product |
ASTM D 7776 : 2012 | Standard Guide for Self-Assessment of Quality System Practices in Petroleum Products and Lubricant Testing Laboratories (Withdrawn 2017) |
ASTM D 5441 : 1998 : R2003 : EDT 1 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
ASTM D 5274 : 2000 | Standard Guide for Analysis of 1,3-Butadiene Product |
ASTM D 5799 : 1995 : R2000 : EDT 1 | Standard Test Method for Determination of Peroxides in Butadiene |
ASTM D 5799 : 1995 : R2004 | Standard Test Method for Determination of Peroxides in Butadiene |
DIN EN ISO 4257:2002-03 | LIQUEFIED PETROLEUM GASES - METHOD OF SAMPLING |
API MPM CH8.5 : 2015 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.5: STANDARD PRACTICE FOR MANUAL PISTON CYLINDER SAMPLING FOR VOLATILE CRUDE OILS, CONDENSATES, AND LIQUID PETROLEUM PRODUCTS |
14/30283904 DC : 0 | BS 4250 - SPECIFICATION FOR COMMERCIAL BUTANE AND COMMERCIAL PROPANE |
API TR 2572 : 2013 | CARBON CONTENT, SAMPLING, AND CALCULATION |
ASTM D 5799 : 1995 : R2009 | Standard Test Method for Determination of Peroxides in Butadiene |
API MPM CH17.10.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 17.10: MEASUREMENT OF CARGOES ON BOARD MARINE GAS CARRIERS - PART 2: LIQUEFIED PETROLEUM AND CHEMICAL GASES |
ASTM D 5273 : 1992 : R2002 | Standard Guide for Analysis of Propylene Concentrates |
ASTM D 7828 : 2012 | Standard Test Method for Determination of Residue Composition in Liquefied Petroleum Gas (LPG) Using Automated Thermal Desorption/Gas Chromatography (ATD/GC) (Withdrawn 2021) |
ASTM D 5273 : 1992 : R2012 | Standard Guide for Analysis of Propylene Concentrates |
API MPMS CH8.5 SPANISH : 2015 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.5: STANDARD PRACTICE FOR MANUAL PISTON CYLINDER SAMPLING FOR VOLATILE CRUDE OILS, CONDENSATES, AND LIQUID PETROLEUM PRODUCTS |
ASTM D 6897 : 2016 : REDLINE | Standard Test Method for Vapor Pressure of Liquefied Petroleum Gases (LPG) (Expansion Method) |
ASTM D 5799 : 1995 : R2014 | Standard Test Method for Determination of Peroxides in Butadiene |
ASTM D 1265 : 2011 | Standard Practice for Sampling Liquefied Petroleum (LP) Gases, Manual Method |
ASTM D 7901 : 2014 | Standard Specification for Dimethyl Ether for Fuel Purposes |
ASTM UOP 930 : 2007 | Chloride in LPG and Gaseous Hydrocarbons by Dry Colorimetry |
ASTM D 5441 : 1998 : R2013 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
BS 4250:1997 | Specification for commercial butane and commercial propane |
BS 4250:2014 | Specification for commercial butane and commercial propane |
ASTM D 7796 : 2017 : REDLINE | Standard Test Method for Analysis of Ethyl tert-Butyl Ether (ETBE) by Gas Chromatography |
ASTM D 5274 : 2000 : R2014 | Standard Guide for Analysis of 1,3–Butadiene Product |
BS 4250-1:1987 | Liquefied petroleum gas Specification for commercial butane and propane |
API MPM CH8.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.2: STANDARD PRACTICE FOR AUTOMATIC SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
ASTM D 5134 : 2013 : R2017 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 5134 : 2013 | Standard Test Method for Detailed Analysis of Petroleum Naphthas through n-Nonane by Capillary Gas Chromatography |
ASTM D 6730 : 2001 : R2006 : EDT 1 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 5441 : 1998 : R2017 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
ASTM D 6377 : 2016 : REDLINE | Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCR<inf>x</inf > (Expansion Method) |
ASTM D 8003 : 2015 | Standard Test Method for Determination of Light Hydrocarbons and Cut Point Intervals in Live Crude Oils and Condensates by Gas Chromatography |
ISO 4257:2001 | Liquefied petroleum gases Method of sampling |
EN ISO 4257:2001 | Liquefied petroleum gases - Method of sampling (ISO 4257:2001) |
ASTM D 6730 : 2001 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 6730 : 2001 : R2016 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 1838 : 2016 : REDLINE | Standard Test Method for Copper Strip Corrosion by Liquefied Petroleum (LP) Gases |
ASTM D 6730 : 2001 : R2006 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
ASTM D 5441 : 1998 : R2008 : EDT 1 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
API MPM CH8.1 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
ASTM D 5441 : 1998 | Standard Test Method for Analysis of Methyl Tert-Butyl Ether (MTBE) by Gas Chromatography |
BS 2000-477(2001) : 2001 | METHODS OF TEST FOR PETROLEUM AND ITS PRODUCTS - LIQUEFIED PETROLEUM GASES - METHOD OF SAMPLING |
ASTM D 8009 : 2015 | Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products |
ASTM D 6849 : 2013 : REDLINE | Standard Practice for Storage and Use of Liquefied Petroleum Gases (LPG) in Sample Cylinders for LPG Test Methods |
ASTM D 1265 : 2011 : R2017 : EDT 1 | Standard Practice for Sampling Liquefied Petroleum (LP) Gases, Manual Method |
ASTM D 6730 : 2001 : R2011 | Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100–Metre Capillary (with Precolumn) High-Resolution Gas Chromatography |
BS EN ISO 4257:2001 | Methods of test for petroleum and its products. Liquefied petroleum gases. Method of sampling |
ASTM D 8009 : 2015 | Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products |
GPA 2140 : 2017 | LIQUEFIED PETROLEUM GAS SPECIFICATIONS AND TEST METHODS |
GPA 2174 : 2014 | OBTAINING LIQUID HYDROCARBONS SAMPLES FOR ANALYSIS BY GAS CHROMATOGRAPHY |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.