ASTM D 3704 : 1996 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion
Hardcopy , PDF
20-11-2024
English
15-11-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 05.01, 2018 Defines the determination of wear properties of lubricating greases by means of the Falex block-on-ring friction and wear test machine.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
5
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of wear properties of lubricating greases by means of the Falex block-on-ring friction and wear test machine.
1.2The values stated in SI units are to be regarded as standard except where equipment is supplied using inch-pound units and would then be regarded as standard.
1.2.1Exception—The metric equivalents of inch-pound units given in such cases in the body of the standard may be approximate.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM G 190 : 2015 | Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021) |
| ASTM G 40 : 2021 | Standard Terminology Relating to Wear and Erosion |
| ASTM D 2714 : 1994 : R1998 | Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine |
| ASTM D 1403 : 1997 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 1403 : 2020 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 2714 : 1994 : R2014 | Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine |
| ASTM D 1403 : 2010 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 1403 : 2002 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 1403 : 2020 : REV A | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 2714 : 1994 : R2003 | Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine |
| ASTM D 2714 : 1994 : R2009 | Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine |
| ASTM D 1403 : 2018 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM D 2714 : 1994 : R2019 | Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine |
| ASTM G 40 : 2021 : REV A | Standard Terminology Relating to Wear and Erosion |
| ASTM G 40 : 2022 | Standard Terminology Relating to Wear and Erosion |
| ASTM G 40 : 2022 : REV A | Standard Terminology Relating to Wear and Erosion |
| ASTM D 1403 : 2002 : R2007 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
| ASTM G 40 : 2017 | Standard Terminology Relating to Wear and Erosion |
| ASTM D 1403 : 2019 | Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.