ASTM D 4050 : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for (Field Procedure) for Withdrawal and Injection Well Testing for Determining Hydraulic Properties of Aquifer Systems
25-02-2020
English
01-06-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.08, 2017 Defines the field procedure for selecting well locations, controlling change (discharge or injection) rates, and measuring water levels used to analyze the hydraulic properties of an aquifer or aquifers and adjacent confining beds.
| Committee |
D 18
|
| DocumentType |
Redline
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers the field procedure for selecting well locations, controlling change (discharge or injection) rates, and measuring water levels used to analyze the hydraulic properties of an aquifer or aquifers and adjacent confining beds.
1.2This test method is used in conjunction with an analytical procedure such as Test Methods D4105 or D4106 to evaluate the data and determine aquifer properties.
1.3The appropriate field and analytical procedures are selected as described in Guide D4043.
1.4Limitations—The limitations of this test method are primarily related to the correspondence between the field situation determined by this test method and the simplifying assumptions of the analytical Test Methods D4105 or D4106 and D4043.
1.5The values stated in SI units are to be regarded as standard.
1.6All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.6.1The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 5472 : 1993 : R2005 | Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well (Withdrawn 2014) |
| ASTM D 6914 : 2004 | Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices |
| ASTM D 5270 : 1996 : R2014 | Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers |
| ASTM D 6914 : 2004 : EDT 1 | Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices |
| ASTM D 6028 : 2017 : REDLINE | Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer Taking into Consideration Storage of Water in Leaky Confining Beds by Modified Hantush Method |
| ASTM D 5269 : 2015 : REDLINE | Standard Test Method for Determining Transmissivity of Nonleaky Confined Aquifers by the Theis Recovery Method |
| ASTM D 5850 : 2018 : REDLINE | Standard Test Method for (Analytical Procedure) Determining Transmissivity, Storage Coefficient, and Anisotropy Ratio from a Network of Partially Penetrating Wells |
| ASTM D 5270 : 1996 | Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers |
| ASTM D 5472 : 1993 : R1999 : EDT 1 | Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well |
| ASTM D 5270 : 1996 : R2002 | Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers |
| ASTM D 420 : 2018 | Standard Guide for Site Characterization for Engineering Design and Construction Purposes |
| ASTM D 5472/D5472M : 2014 | Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well |
| ASTM D 6034 : 2017 : REDLINE | Standard Test Method (Analytical Procedure) for Determining the Efficiency of a Production Well in a Confined Aquifer from a Constant Rate Pumping Test |
| ASTM E 1943 : 1998 | Standard Guide for Remediation of Ground Water by Natural Attenuation at Petroleum Release Sites |
| ASTM D 5473 : 1993 : R2006 | Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer (Withdrawn 2015) |
| ASTM E 1943 : 1998 : R2004 | Standard Guide for Remediation of Ground Water by Natural Attenuation at Petroleum Release Sites |
| ASCE 34 01 : 2001 | STANDARD GUIDELINES FOR ARTIFICIAL RECHARGE OF GROUND WATER |
| ASTM D 5920 : 2014 | Standard Test Method [Analytical Procedure] for Tests of Anisotropic Unconfined Aquifers by Neuman Method |
| ASTM D 5730 : 2004 | Standard Guide for Site Characterization for Environmental Purposes With Emphasis on Soil, Rock, the Vadose Zone and Groundwater (Withdrawn 2013) |
| ASTM D 5473 : 1993 : R2000 | Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer |
| ASTM D 5473/D5473M : 2015 | Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer |
| ASTM E 1943 : 1998 : R2010 | Standard Guide for Remediation of Ground Water by Natural Attenuation at Petroleum Release Sites |
| ASTM D 4106 : 2015 : REDLINE | Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method |
| ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6914/D6914M : 2016 : REDLINE | Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices |
| ASTM D 6914 : 2004 : R2010 | Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices |
| ASTM D 5270 : 1996 : R2008 | Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers |
| ASTM E 1943 : 1998 : R2015 | Standard Guide for Remediation of Ground Water by Natural Attenuation at Petroleum Release Sites (Withdrawn 2024) |
| ASTM D 6029 : 2017 : REDLINE | Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer and a Leaky Confining Bed with Negligible Storage by the Hantush-Jacob Method |
| ASTM D 4106 : 2015 : REDLINE | Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method |
| ASTM D 4043 : 2017 : REDLINE | Standard Guide for Selection of Aquifer Test Method in Determining Hydraulic Properties by Well Techniques |
| ASTM D 4044 : 1996 | Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifiers |
| ASTM D 3740 : 2012-06 | PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION |
| ASTM D 6026 : 2013 : REDLINE | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 653 : 2014 : REDLINE | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.