ASTM D 4084 : 2007 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
Hardcopy , PDF
17-03-2024
English
05-12-2017
CONTAINED IN VOL. 05.06, 2017 Defines the determination of hydrogen sulfide (H[2]S) in gaseous fuels.
Committee |
D 03
|
DocumentType |
Test Method
|
Pages |
7
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the determination of hydrogen sulfide (H2S) in gaseous fuels. It is applicable to the measurement of H2S in natural gas, liquefied petroleum gas (LPG), substitute natural gas, landfill gas, sewage treatment off gasses, recycle gas, flare gasses, and mixtures of fuel gases. This method can also be used to measure the hydrogen sulfide concentration in carbon dioxide. Air does not interfere. The applicable range is 0.1 to 16 parts per million by volume (ppm/v) (approximately 0.1 to 22 mg/m3) and may be extended to 100 % H2S by manual or automatic volumetric dilution.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6021 : 2012 : R2017 | Standard Test Method for Measurement of Total Hydrogen Sulfide in Residual Fuels by Multiple Headspace Extraction and Sulfur Specific Detection |
ASTM D 7800/D7800M : 2014 | Standard Test Method for Determination of Elemental Sulfur in Natural Gas (Withdrawn 2023) |
ASTM D 7165 : 2010 : R2015 | Standard Practice for Gas Chromatograph Based On-line/At-line Analysis for Sulfur Content of Gaseous Fuels |
ASTM D 7165 : 2022 | Standard Practice for Gas Chromatograph Based On-line/At-line Analysis for Sulfur Content of Gaseous Fuels |
ASTM D 6021 : 2022 | Standard Test Method for Measurement of Total Hydrogen Sulfide in Residual Fuels by Multiple Headspace Extraction and Sulfur Specific Detection |
ASTM D 4323 : 2021 | Standard Test Method for Hydrogen Sulfide in the Atmosphere by Rate of Change of Reflectance |
ASTM D 4323 : 2015 | Standard Test Method for Hydrogen Sulfide in the Atmosphere by Rate of Change of Reflectance |
ASTM D 1914 : 1995 : R2022 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres |
ASTM D 2420 : 1991 : R1996 : EDT 1 | Standard Test Method for Hydrogen Sulfide In Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 3609 : 2000 : R2014 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM D 2420 : 2013 : R2018 | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
ASTM D 7166 : 2005 | Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels |
ASTM E 2165 : 2001 | Standard Practice for Establishing an Uncertainty Budget for the Chemical Analysis of Metals, Ores, and Related Materials (Withdrawn 2007) |
ASTM D 2420 : 2012 | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 7166 : 2010 : R2015 | Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels |
ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
ASTM D 3609 : 2000 : R2005 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM D 7166 : 2023 | Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels |
ASTM D 3609 : 2000 : R2010 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM D 7166 : 2010 | Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels |
ASTM D 2420 : 2012 : REV A | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 3609 : 2022 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
ASTM D 3609 : 2000 | Standard Practice for Calibration Techniques Using Permeation Tubes |
ASTM D 1914 : 1995 : R1999 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis Atmospheres |
ASTM D 2420 : 2007 | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 1914 : 1995 : R2014 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres |
ASTM D 2420 : 2023 | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
ASTM D 1914 : 1995 : R2010 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres |
ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
ASTM D 1914 : 1995 : R2004 : EDT 1 | Standard Practice for Conversion Units and Factors Relating to Sampling and Analysis of Atmospheres |
ASTM D 2420 : 2013 | Standard Test Method for Hydrogen Sulfide in Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
ASTM D 2420 : 1991 : R2001 | Standard Test Method for Hydrogen Sulfide In Liquefied Petroleum (LP) Gases (Lead Acetate Method) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.