
ASTM D 4628 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by

Standard Test Method for Analysis of Barium, Calcium, Magnesium, and Zinc in Unused Lubricating Oils by Atomic Absorption Spectrometry
13-06-2023
English
18-01-2017
CONTAINED IN VOL. 05.02, 2017 Defines the determination of mass percent barium from 0.005 to 1.0%, calcium and magnesium from 0.002 to 0.3%, and zinc from 0.002 to 0.2% in lubricating oils.
Committee |
D 02
|
DocumentType |
Redline
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This test method is applicable for the determination of mass percent barium from 0.005 % to 1.0 %, calcium and magnesium from 0.002 % to 0.3 %, and zinc from 0.002 % to 0.2 % in lubricating oils.
1.2Higher concentrations can be determined by appropriate dilution. Lower concentrations of metals such as barium, calcium, magnesium, and zinc at about 10 ppm level can also be determined by this test method. Use of this test method for the determination at these lower concentrations should be by agreement between the buyer and the seller.
1.3Lubricating oils that contain viscosity index improvers may give low results when calibrations are performed using standards that do not contain viscosity index improvers.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 3.1, 6.3, and 8.1.
MIL-L-46152 Revision E:1990 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, ADMINISTRATIVE SERVICE, METRIC |
MIL L 21260 : D | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE AND BREAK IN |
MIL L 2105 : D | LUBRICATING OIL, GEAR, MULTI PURPOSE |
MIL-PRF-46167 Revision D:2005 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, ARCTIC |
ASTM D 7578 : 2015-06 | GUIDE FOR CALIBRATION REQUIREMENTS FOR ELEMENTAL ANALYSIS OF PETROLEUM PRODUCTS AND LUBRICANTS |
ASTM D 7740 : 201 | Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants |
A-A-52306 Revision A:1995 | LUBRICATING OIL, HEAVY-DUTY DIESEL ENGINE |
ASTM D 4951 : 2014 : REDLINE | Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM D 7876 : 2013 | Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants |
ASTM D 6074 : 2015 : REDLINE | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 8110 : 2017 | Standard Test Method for Elemental Analysis of Distillate Products by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) |
SAE J2359_199811 | Lubricating Oil, Internal Combustion Engine, Military Combat/Tactical Service |
MIL PRF 009000 : K | LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH-OUTPUT DIESEL |
MIL-PRF-9000 Revision L:2014 | Lubricating Oil, Shipboard Internal Combustion Engine, High-Output Diesel |
MIL-PRF-21260 Revision E:1998 | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, PRESERVATIVE BREAK-IN |
SAE J357_201601 | Physical and Chemical Properties of Engine Oils |
ASTM D 6443 : 2014 : REDLINE | TEST METHOD FOR DETERMINATION OF CALCIUM, CHLORINE, COPPER, MAGNESIUM, PHOSPHORUS, SULFUR, AND ZINC IN UNUSED LUBRICATING OILS AND ADDITIVES BY WAVELENGTH DISPERSIVE X-RAY FLUORESCENCE SPECTROMETRY (MATHEMATICAL CORRECTION PROCEDURE) |
SAE J2361_199811 | Lubricating Oil, Internal Combustion Engine, Preservation Break-In |
MIL L 9000 : H | LUBRICATING OIL, SHIPBOARD INTERNAL COMBUSTION ENGINE, HIGH OUTPUT DIESEL |
MIL L 2104 : F | LUBRICATING OIL, INTERNAL COMBUSTION ENGINE, COMBAT TACTICAL SERVICE |
ASTM D 7740 : 2011 : R2016 | Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants |
ASTM D 4997 : 1989 | Test Methods for Evaluation of Water Sensitivity of Multi-Purpose Power Transmission Fluids (Withdrawn 1995) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.