ASTM D 4673 : 2016 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
17-02-2023
English
08-04-2016
CONTAINED IN VOL. 08.03, 2016 Describes only ABS materials and ABS alloys suitable for injection molding and extrusion.
Committee |
D 20
|
DevelopmentNote |
Supersedes ASTM D 3011. (02/2002)
|
DocumentType |
Redline
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This classification system covers only ABS materials and ABS alloys suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding. Recycle ABS and alloys will be addressed in a separate standard.
1.2This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Materials are to be selected by personnel with expertise in the plastics field where the economics, the environment to be encountered, the inherent properties of the materials, the part design, the part performance required, and the manufacturing process to be employed all enter into the selection.
1.3The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are addressed by using the suffixes given in Section 5.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5The following precautionary caveat pertains only to the test methods portion, Section 12, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:This standard and ISO 2580 address the same subject matter, but differ in technical content.
MIL-M-87113 Revision A:1993 | MASK, OXYGEN, MBU-10/P |
MIL-DTL-83425 Revision A:2006 | EARCUP, SOUND PROTECTIVE MX-8376/AR |
16/30338304 DC : 0 | BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS |
A-A-55469 Revision B:2015 | CONNECTORS, ELECTRICAL, PLUGS, TIP (TEST POINT PLUG, BANANA PLUG) GENERAL REQUIREMENTS FOR |
ASTM D 1939 : 1994 | Practice for Determining Residual Stresses in Extruded or Molded Acrylonitrile-Butadiene-Styrene (ABS) Parts by Immersion in Glacial Acetic Acid (Withdrawn 1999) |
MIL-DTL-642 Revision F:2015 | Plugs, Telephone, and Accessory Screws General Specification for |
SAE J 2642 : 2017 | RECOMMENDED PRACTICE FOR DEVELOPING SPECIFICATIONS FOR AUTOMOTIVE THERMOPLASTIC MATERIALS |
ANSI/AWWA C710 : 2015 | COLD-WATER METERS - DISPLACEMENT TYPE, PLASTIC MAIN CASE |
AWWA C700 : 2015 | COLD-WATER METERS - DISPLACEMENT TYPE, METAL ALLOY MAIN CASE |
ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
MIL-DTL-22442-1 Revision C:1998 | Cable Assemblies, Aircraft Audio, Switch Assembly |
MS90578 Revision C:2012 | ADAPTER, CONNECTOR, (TWIN BINDING POST-BNC MALE) TYPE UG-1441/U |
MIL-DTL-641 Revision G:2015 | Jacks, Telephone General Specification for |
AWWA C704 : 2015 | PROPELLER-TYPE METERS FOR WATERWORKS APPLICATIONS |
SAE AS 81969 : 2016 | INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, GENERAL SPECIFICATION FOR |
CSA M671 : 1999 | SLOW-MOVING VEHICLE IDENTIFICATION EMBLEM |
ASAE S276.4 : 1994 | AGRICULTURAL EQUIPMENT - SLOW-MOVING VEHICLE IDENTIFICATION EMBLEM |
MIL P 642 : D | PLUG, TELEPHONE AND ACCESSORY SCREWS, GENERAL SPECIFICATION FOR |
MIL-DTL-52543 Revision E:2010 | LIGHT, MARKER, GROUND-OBSTRUCTION |
CSA A440 : 2017 | NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS |
ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ISO 294:1995 | Plastics Injection moulding of test specimens of thermoplastic materials |
ASTM D 3641 : 2015 : REDLINE | Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials |
ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
ISO 2580-2:2003 | Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
ASTM D 1525 : 2017 | Standard Test Method for Vicat Softening Temperature of Plastics |
ASTM D 1003 : 2013 : REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 5630 : 2013 : REDLINE | Standard Test Method for Ash Content in Plastics (Withdrawn 2022) |
ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
ASTM D 648 : 2016 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
ISO 179:1993 | Plastics Determination of Charpy impact strength |
ISO 20753:2008 | Plastics Test specimens |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.