ASTM D 473 : 2007 : R2017 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method
Hardcopy , PDF
18-07-2022
English
01-08-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.This test method covers the determination of sediment in crude oils and fuel oils by extraction with toluene.
| Committee |
D 02
|
| DevelopmentNote |
Also numbered as IP 53 Also numbered as API MPM CH10.1 (10/2002)
|
| DocumentType |
Test Method
|
| Pages |
6
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the determination of sediment in crude oils and fuel oils by extraction with toluene. The precision applies to a range of sediment levels from 0.01 % to 0.40 % mass, although higher levels may be determined.
Note 1:Precision on recycled oils and crankcase oils is unknown and additional testing is required to determine that precision.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 5.1.1.6 and 6.1.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4807 : 2005 : R2020 | Standard Test Method for Sediment in Crude Oil by Membrane Filtration |
| ASTM G 205 : 2016 | Standard Guide for Determining Emulsion Properties, Wetting Behavior, and Corrosion-Inhibitory Properties of Crude Oils |
| ASTM D 5439 : 1995 : R2019 | Standard Test Method for Determination of Sediment in Moellon |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 128 : 1998 : R2019 | Standard Test Methods for Analysis of Lubricating Grease |
| ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 6823 : 2008 : R2021 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ISO 5272:1979 | Toluene for industrial use — Specifications |
| API MPM CH8.1 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| API MPM CH8.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.2: STANDARD PRACTICE FOR AUTOMATIC SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.