ASTM D 4972 : 2019 : R2024 : EDT 1
Current
The latest, up-to-date edition.
Standard Test Methods for pH of Soils
Hardcopy , PDF
English
01-07-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
6
|
| ProductNote |
ε1 NOTE—Reapproved with editorial changes in July 2024.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover the measurement of the pH of soils that will pass the 2.00 mm (No. 10) sieve. Such measurements are used in the agricultural, environmental, geotechnical, and natural resources fields. This measurement determines the degree of acidity or alkalinity in soil materials suspended in water and a 0.01 M calcium chloride solution. Measurements in both liquids are necessary to fully define the soil's pH. This variable is useful in determining the solubility of soil minerals and the mobility of ions in the soil and assessing the viability of the soil-plant environment. A more detailed discussion of the usefulness of this parameter is given in Refs (1-6)2.
1.2Two methods for measuring the pH of soils are provided. The method to be used shall be specified by the requesting authority. When no method is specified, Method A shall be used. The pH is measured in test water and a calcium chloride solution for both methods.
1.2.1Method A—The pH is measured using a potentiometer having a pH sensitive electrode system. This method can be used for any application and must be used when the application warrants a higher level of resolution.
1.2.2Method B—The pH is measured using pH sensitive paper. This method can be used for any application, however, because paper typically has a lower resolution, it provides an approximate estimate of the pH of the soil and should not be used when the application requires a higher level of resolution (Note 1).
Note 1:For example, paper with a sensitivity to the nearest 1 pH unit placed into a buffer solution of 4 should indicate a pH of 4, however, it would not indicate if the pH is 4.449 or 3.449.
1.3Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4All measured and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.4.1The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8262 : 2022 | Standard Test Method for Determining the pH of Granular Material for Use in Embankments, Subgrades, and Retaining Wall Backfil |
| ASTM E 2278 : 2013 : R2019 | Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage |
| ASTM D 5268 : 2023 | Standard Specification for Topsoil Used for Landscaping and Construction Purposes |
| ASTM D 5988 : 2018 | Standard Test Method for Determining Aerobic Biodegradation of Plastic Materials in Soil |
| ASTM D 8151 : 2019 : EDT 1 | Standard Practice for Obtaining Rainfall Runoff from Unvegetated Rolled and Hydraulic Erosion Control Products (RECPs and HECPs) for Acute Ecotoxicity Testing |
| ASTM D 7100 : 2011 : R2020 | Standard Test Method for Hydraulic Conductivity Compatibility Testing of Soils with Aqueous Solutions |
| ASTM F 2747 : 2019 | Standard Guide for Construction of Sand-based Rootzones for Golf Putting Greens and Tees |
| ASTM D 7294 : 2013 : R2021 | Standard Guide for Collecting Treatment Process Design Data at a Contaminated Site—A Site Contaminated with Chemicals of Interest |
| ASTM F 2396 : 2011 : R2019 | Standard Guide for Construction of High Performance Sand-Based Rootzones for Athletic Fields |
| ASTM E 2277 : 2014(R2019) | Standard Guide for Design and Construction of Coal Ash Structural Fills |
| ASTM D 2976 : 2022 : REV A | Standard Test Method for pH of Peat Materials |
| ASTM E 2060 : 2022 | Standard Guide for Use of Coal Combustion Products for Solidification/Stabilization of Inorganic Wastes |
| ASTM E 2243 : 2013 : R2019 | Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation |
| ASTM F 3339 : 2020 | Standard Guide for Construction or Renovation of Native-soil Athletic Fields |
| ASTM D 1193 : 2024 | Standard Specification for Reagent Water |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.