• Shopping Cart
    There are no items in your cart

ASTM D 5026 : 2015 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension

Available format(s)

PDF

Superseded date

25-11-2023

Language(s)

English

Published date

20-07-2015

€59.22
Excluding VAT

CONTAINED IN VOL. 08.02, 2015 Defines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular specimens molded directly or cut from sheets, plates, or molded shapes.

Committee
D 20
DocumentType
Redline
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This test method outlines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular specimens molded directly or cut from sheets, plates, or molded shapes. The tensile data generated may be used to identify the thermomechanical properties of a plastic material or composition using a variety of dynamic mechanical instruments.

1.2This test method is intended to provide a means for determining viscoelastic properties of a wide variety of plastic materials using nonresonant forced-vibration techniques, in accordance with Practice D4065. Plots of the elastic (storage) modulus; loss (viscous) modulus; complex modulus and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of the polymeric material system.

1.3This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz.

1.4Apparent discrepancies may arise in results obtained under differing experimental conditions. These apparent differences from results observed in another study can usually be reconciled, without changing the observed data, by reporting in full (as described in this test method) the conditions under which the data were obtained.

1.5Due to possible instrumentation compliance, the data generated are intended to indicate relative and not necessarily absolute property values.

1.6Test data obtained by this test method are relevant and appropriate for use in engineering design.

1.7The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:This test method is technically equivalent to ISO 6721, Part 4.

ASTM D 6382/D6382M : 1999 : R2011 : EDT 1 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
ASTM D 6382 : 1999 : R2005 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
ASTM D 6382 : 1999 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
ASTM D 4065 : 2012 : REDLINE Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 6382/D6382M : 1999 : R2017 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
IEEE 1310-2012 REDLINE IEEE Recommended Practice for Thermal Cycle Testing of Form-Wound Stator Bars and Coils for Large Rotating Machines
A500-16 Building guards

ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ISO 6721-4:2008 Plastics Determination of dynamic mechanical properties Part 4: Tensile vibration Non-resonance method
ASTM D 4065 : 2012 : REDLINE Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.