ASTM D 558/D558M : 2019
Current
The latest, up-to-date edition.
Standard Test Methods for Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures
Hardcopy , PDF
English
01-01-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1These test methods cover the determination of the relationship between the water content and the density of soil-cement mixtures when compacted before cement hydration as prescribed.
1.2A 0.0333-ft3 [944-cm3] mold and a 5.50-lbf [24.5-N or mass of 2.5-kg] rammer dropped from a height of 12.0 in. [30.5 cm] are used and two methods, depending on soil gradation, are covered, as follows:
| Sections | |
| Test Method A, using soil material passing a No. 4 [4.75-mm] sieve. This method shall be used when 100 % of the soil sample passes the No. 4 [4.75-mm] sieve | |
| Test Method B, using soil material passing a 3/4-in. [19.0-mm] sieve. This method shall be used when part of the soil sample is retained on the No. 4 [4.75-mm] sieve. This test method may be used only on materials with 30 % or less retained on the 3/4-in. [19.0-mm] sieve | |
1.3Units—The values stated in inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3.1The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The slug unit is not given, unless dynamic (F=ma) calculations are involved.
1.3.2It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. This standard includes the gravitational system of inch-pound units and does not use/present the slug unit for mass. However, the use of balances or scales recording pounds of mass (lbm) or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard.
1.4All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.4.1The procedures used to specify how data are collected/recorded and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for the engineering design.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 150/C150M : 2024 | Standard Specification for Portland Cement |
| ASTM E 11 : 2024 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM D 4753 : 2024 | Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing |
| ASTM D 653 : 2024 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM D 653 : 2022 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 559/D559M : 2015 : R2023 | Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures |
| ASTM D 560/D560M : 2024 | Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures |
| ASTM C 595/C595M : 2024 | Standard Specification for Blended Hydraulic Cements |
| ASTM C 595/C595M : 2023 | Standard Specification for Blended Hydraulic Cements |
| ASTM D 653 : 2024 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 560/D560M : 2016 | Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures |
| ASTM C 150/C150M : 2022 | Standard Specification for Portland Cement |
| ASTM D 559/D559M : 2015 : R2023 : EDT 1 | Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.