• Shopping Cart
    There are no items in your cart

ASTM D 5630 : 2006

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Test Method for Ash Content in Plastics

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Superseded by

ASTM D 5630 : 2013

Language(s)

English

Published date

01-09-2006

€67.30
Excluding VAT

Committee
D 20
DocumentType
Test Method
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1 This test method was developed to determine the inorganic content of plastics by destructive ashing procedures. Ash levels of 0.01 % or above are covered by this test method.

1.2 These ashing procedures are used only to quantify the residual solids in the polymer and can not be used to identify the individual chemical components of the ash, qualitatively.

1.3 This test method is limited to those materials (including glass) that are stable to 900°C. Test Method D 2584 is recommended for unknown samples, and in instances where fusion of the inorganic portions may be of concern.

1.4 Fluorinated polymers and polymers containing halogenated components have not been included in these procedures.

1.5 Two procedures for determining the inorganic residue in plastics are listed as follows:

1.5.1 Procedure A Muffle-Furnace Technique- For 5 - 50 gram samples. Samples are flamed over a burner prior to being ashed in a muffle furnace.

1.5.2 Procedure B Rapid-Ash Muffle-Furnace Technique- For 5 - 50 gram samples. Samples are ignited and ashed in a muffle furnace. For more efficient ashing, the plastic sample should be in the form of powder or pellet.

Note 1

Procedure B is similar to ISO 3451/1-1981(E).

1.6 The values stated in SI units are to be regarded as the standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for specific precautionary statements.

ASTM D 4067 : 2016 Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 5740 : 2018 Standard Guide for Writing Material Standards in the Classification D4000 Format
ASTM D 6394 : 2014 Standard Specification for Sulfone Plastics (SP)
ASTM D 3935 : 2015 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
ASTM D 4549 : 2015 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)
ASTM D 5205 : 2016 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM D 5138 : 2016 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM D 6339 : 2011 : R2019 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)
ASTM D 5336 : 2015 : REV A Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material
ASTM D 6778 : 2014 Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 4673 : 2016 Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
ASTM F 2306/F2306M : 2019 Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
ASTM F 2648/F2648M : 2017 Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
ASTM A 978/A978M : 2008 : R2013 Standard Specification for Composite Ribbed Steel Pipe, Precoated and Polyethylene Lined for Gravity Flow Sanitary Sewers, Storm Sewers, and Other Special Applications (Withdrawn 2020)
ASTM F 628 : 2012 : EDT 3 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.