![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 5687/D5687M : 1995 : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation
Hardcopy , PDF
10-11-2020
English
14-12-2015
This guide provides guidelines to facilitate the proper preparation of laminates and test specimens from fiber-reinforced organic matrix composite prepregs.
Committee |
D 30
|
DocumentType |
Guide
|
Pages |
16
|
ProductNote |
Reconfirmed 2015
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This guide provides guidelines to facilitate the proper preparation of laminates and test specimens from fiber-reinforced organic matrix composite prepregs. The scope is limited to organic matrices and fiber reinforcement in unidirectional (tape) or orthagonal weave patterns. Other forms may require deviations from these general guidelines. Other processing techniques for test coupon preparation, for example, pultrusion, filament winding and resin-transfer molding, are not addressed.
1.2Specimen preparation is modeled as an 8-step process that is presented in Fig. 1 and Section 8. Laminate consolidation techniques are assumed to be by press or autoclave. This practice assumes that the materials are properly handled by the test facility to meet the requirements specified by the material supplier(s) or specification, or both. Identification and information gathering guidelines are modeled after Guide E1309. Test specimens shall be directly traceable to material used as designated in Guide E1434. Proper test specimen identification also includes designation of process equipment, process steps, and any irregularities identified during processing.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 3171 : 1999 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3990 : 1999 : R2008 | Standard Terminology Relating to Fabric Defects |
ASTM D 3990 : 1999 : R2004 | Standard Terminology Relating to Fabric Defects |
ASTM D 3163 : 2001 | Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
ASTM D 3878 : 2002 : REV A | Standard Terminology for Composite Materials |
ASTM D 4850 : 2002 | Standard Terminology Relating to Fabric |
ASTM D 5229/D5229M : 2014-06 | TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS |
ASTM E 1237 : 1993 : R1998 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 3990 : 2012 : R2016 | Standard Terminology Relating to Fabric Defects |
ASTM D 4850 : 2002 : REV A | Standard Terminology Relating to Fabric |
ASTM D 3878 : 2015 | Standard Terminology for Composite Materials |
ASTM E 1434 : 2000 : R2013 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015) |
ASTM D 3878 : 2019 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2000 | Standard Terminology Composite Materials |
ASTM D 4850 : 2003 : REV A : R2007 | Standard Terminology Relating to Fabric |
ASTM D 4850 : 2008 : EDT 1 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM D 3171 : 2011 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 4850 : 2013 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM D 2734 : 2016 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM D 4850 : 2012 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM C 297/C297M : 2016 : REDLINE | Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions |
ASTM D 3878 : 2003 : REV A | Standard Terminology for Composite Materials |
ASTM E 1237 : 1993 : R2009 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 3878 : 2016 | Standard Terminology for Composite Materials |
ASTM E 1309 : 2000 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 3878 : 2019 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 2020 : REV A | Standard Terminology for Composite Materials |
ASTM D 3878 : 1998 | Standard Terminology Composite Materials |
ASTM D 3878 : 2018 | Standard Terminology for Composite Materials |
ASTM D 3990 : 2012 : EDT 1 | Standard Terminology Relating to Fabric Defects |
ASTM D 4850 : 2013 : R2017 : EDT 1 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM E 1434 : 2000 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM D 3171 : 2009 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3878 : 2002 | Standard Terminology for Composite Materials |
ASTM E 1237 : 1993 : R2003 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 4850 : 2008 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM D 2734 : 2016 : REDLINE | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3163 : 2001 : R2008 | Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
ASTM D 4850 : 2003 | Standard Terminology Relating to Fabric |
ASTM D 3171 : 2015 : REDLINE | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3878 : 2004 | Standard Terminology for Composite Materials |
ASTM E 1237 : 1993 : R2014 | Standard Guide for Installing Bonded Resistance Strain Gages |
ASTM D 2734 : 1994 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 4850 : 2013 : R2017 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
ASTM D 4850 : 2000 : REV A | Standard Terminology Relating to Fabric |
ASTM D 3878 : 2007 : R2013 | Standard Terminology for Composite Materials |
ASTM E 1309 : 2000 : R2011 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015) |
ASTM D 3878 : 2020 : REDLINE | Standard Terminology for Composite Materials |
ASTM D 3531 : 1999 : R2009 | Standard Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg |
ASTM D 3878 : 2020 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2003 | Standard Terminology for Composite Materials |
ASTM D 3878 : 2007 | Standard Terminology for Composite Materials |
ASTM D 3531 : 1999 : R2004 | Standard Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg |
ASTM D 2734 : 2009 | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3171 : 1999 : R2004 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 1309 : 2000 : R2005 | Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases |
ASTM D 4850 : 2003 : REV A | Standard Terminology Relating to Fabric |
ASTM D 3990 : 1999 | Standard Terminology Relating to Fabric Defects |
ASTM D 3171 : 2015 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3531 : 1999 | Standard Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg |
ASTM D 3163 : 1996 | Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
ASTM D 3878 : 2004 : REV A | Standard Terminology for Composite Materials |
ASTM D 3171 : 2006 | Standard Test Methods for Constituent Content of Composite Materials |
ASTM E 1434 : 2000 : R2006 | Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases |
ASTM D 3990 : 2012 | Standard Terminology Relating to Fabric Defects |
ASTM D 3878 : 2001 | Standard Terminology Composite Materials |
ASTM D 3163 : 2001 : R2014 | Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
ASTM D 4850 : 2013 : EDT 1 | Standard Terminology Relating to Fabrics and Fabric Test Methods |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.