ASTM D 5893/D5893M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Cold Applied, Single Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements
Hardcopy , PDF
18-05-2021
English
28-07-2016
Committee |
D 04
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers cold applied, single component, chemically curing silicone sealants that are based on polymers of polysiloxane structures and are intended for use in sealing joints and cracks in portland cement concrete highway and airfield pavements. The specification includes both non-sag and self-leveling types of sealants.
1.1.1This specification does not purport to cover the properties required of sealants for use in areas of portland cement concrete pavements subject to jet fuel or other fuel spillage, such as vehicle or aircraft refueling and maintenance areas, or a combination thereof.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Appendix X1.
ASTM E 2785 : 2014 | Standard Test Method for Exposure of Firestop Materials to Severe Environmental Conditions |
ASTM D 5329 : 2016 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
ASTM D 5249 : 2010 : R2016 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
ASTM D 1985 : 1991 : R1997 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
ASTM D 5329 : 2020 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
ASTM C 1183 : 1991 : R1997 | Standard Test Method for Extrusion Rate of Elastomeric Sealants |
ASTM D 5249 : 1995 : R2000 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
ASTM D 2202 : 2000 : R2010 | Standard Test Method for Slump of Sealants |
ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 2202 : 2000 : R2006 | Standard Test Method for Slump of Sealants |
ASTM D 1985 : 2013 : R2019 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
ASTM D 2202 : 2000 | Standard Test Method for Slump of Sealants |
ASTM D 5329 : 2007 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements |
ASTM D 5329 : 2009 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements |
ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
ASTM D 5535 : 1998 | Standard Terminology Relating to Formed-in-Place Sealants for Joints and Cracks in Pavements |
ASTM C 1183 : 2004 | Standard Test Method for Extrusion Rate of Elastomeric Sealants |
ASTM D 2202 : 2000 : R2014 | Standard Test Method for Slump of Sealants |
ASTM C 1183 : 2004 : R2008 | Standard Test Method for Extrusion Rate of Elastomeric Sealants |
ASTM D 5535 : 1998 : R2003 | Standard Terminology Relating to Formed-in-Place Sealants for Joints and Cracks in Pavements (Withdrawn 2009) |
ASTM D 5249 : 1995 : R2006 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
ASTM D 1985 : 2003 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
ASTM D 5249 : 2010 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
ASTM D 5329 : 2004 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements |
ASTM D 5329 : 1996 | Standard Test Methods for Sealants and Fillers, Hot-Applied, For Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements |
ASTM D 2202 : 2000 : R2019 | Standard Test Method for Slump of Sealants |
ASTM D 5329 : 2015 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements |
ASTM D 1985 : 2003 : R2008 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
ASTM D 1985 : 2013 | Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.