ASTM D 619 : 2021
Current
The latest, up-to-date edition.
Standard Test Methods for Vulcanized Fibre Used for Electrical Insulation
Hardcopy , PDF
English
15-02-2021
Committee |
D 09
|
DocumentType |
Test Method
|
Pages |
8
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1These test methods cover the procedures for testing vulcanized fibre sheets, rolls, tubes, and rods of such grades as can be used for electrical insulation.
1.2The procedures appear in the following sections:
Procedure | Section | ||
Arc Resistance | 23 | ||
Ash | 6 | ||
Bond Strength (Ply Adhesion) | 16 | ||
Bursting Strength | 14 | ||
Compressive Strength | 12, 25, 30 | ||
Conditioning | 4 | ||
Density | 17, 26, 32 | ||
Dielectric Strength | 18, 27 | ||
Dimensional Measurements | 28, 33 | ||
Flammability | 22 | ||
Flexural Strength | 13, 31 | ||
Silica | 7 | ||
Tearing Strength | 11 | ||
Tensile Strength | 10, 24, 29 | ||
Thickness (Sheets) | 20 | ||
Resistance to Impact | 15 | ||
Rockwell Hardness | 19 | ||
Volatile Matter | 8 | ||
Water Absorption | 5 | ||
Zinc Chloride | 9 |
1.3The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 7.3, 22.1, and 22.2.
Note 1:The test methods described herein are similar technically to those described in IEC Publication 60667-2. Not all of the tests in this document are included in IEC 60667-2, and the procedures in the two publications are not completely identical; but it is expected that comparable results will be obtained from most of the procedures. Conduct comparative tests if necessary before directly comparing results of tests using the different procedures.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 710 : 2019 | Standard Specification for Vulcanized Fibre Sheets, Rolls, Rods, and Tubes Used for Electrical Insulation |
ASTM D 229 : 2019 : EDT 1 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation |
ASTM D 202 : 2017 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
ASTM D 256 : 2010 : R2018 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 495 : 2014 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
ASTM D 689 : 2017 | Standard Test Method for Internal Tearing Resistance of Paper |
ASTM D 256 : 2023 : EDT 1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 1711 : 2024 : REV A | Standard Terminology Relating to Electrical Insulation |
ASTM D 256 : 2023 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 202 : 2023 | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
ASTM D 1711 : 2024 | Standard Terminology Relating to Electrical Insulation |
ASTM D 785 : 2008 : R2015 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
ASTM D 695 : 2015 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 1711 : 2022 | Standard Terminology Relating to Electrical Insulation |
ASTM D 952 : 2015 : R2021 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
ASTM D 570 : 2022 | Standard Test Method for Water Absorption of Plastics |
ASTM D 1711 : 2020 | Standard Terminology Relating to Electrical Insulation |
ASTM D 785 : 2023 | Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials |
ASTM D 828 : 2016 : EDT 1 | Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus |
ASTM D 695 : 2023 | Standard Test Method for Compressive Properties of Rigid Plastics |
ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
ASTM D 689 : 2017 : R2024 | Standard Test Method for Internal Tearing Resistance of Paper |
ASTM D 6054 : 1997 : R2004 | Standard Practice for Conditioning Electrical Insulating Materials for Testing (Withdrawn 2012) |
ASTM D 495 : 2022 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
ASTM D 828 : 2022 | Standard Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus |
ASTM D 952 : 2015 | Standard Test Method for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.