ASTM D 6279 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings
Hardcopy , PDF
09-12-2020
English
01-02-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers procedures for evaluating the relative mar resistance of a series of high gloss coatings applied to a flat, rigid surface. Wet rub and dry rub abrasion tests are described. To fully characterize a coating's mar resistance, both tests should be run.
Note 1:Dry abrasion mar resistance can also be evaluated by using Test Methods D6037. If a series of very highly mar resistant coatings is being evaluated, Test Methods D6037 will generally provide the better performance discrimination than the dry rub test described here. However, if the equipment described in Test Methods D6037 is not available, the dry rub test described in this test method affords a reasonable alternative. The dry rub test is also useful for evaluating coatings that are not highly mar resistant.
1.2Mar resistance is assessed by measuring the gloss of the abraded and unabraded areas. Mar resistance is directly related to the coating's ability to retain gloss in abraded areas.
Note 2:The mar resistance values obtained by this test method have no absolute significance. They should only be used to derive relative performance rankings for test panels that have been prepared from the series of coatings that are currently being evaluated. If mar resistance values are quoted between laboratories, it is essential that a common standard be measured and that the values be compared to that standard. Even then, the values should be used with caution.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7187 : 2015 | Standard Test Method for Measuring Mechanistic Aspects of Scratch/Mar Behavior of Paint Coatings by Nanoscratching |
| ASTM D 1005 : 1995 : R2020 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 3924 : 2016 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 6037 : 2013 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 6037 : 1996 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 1186 : 1993 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base |
| ASTM D 1005 : 1995 : R2001 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 1400 : 1994 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base |
| ASTM D 3924 : 1980 : R2011 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 6037 : 1996 : R2002 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 3924 : 1980 : R2005 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 6037 : 1996 : R2008 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 1005 : 1995 : R2013 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 6037 : 2018 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 3924 : 1980 : R1996 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
| ASTM D 1005 : 1995 : R2007 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 1005 : 1995 | Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers |
| ASTM D 6037 : 2013 : EDT 1 | Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings |
| ASTM D 3924 : 2016 : R2019 | Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.