• ASTM D 6353 : 2006 : R2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  01-05-2011

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 05.03, 2017 Defines sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks.

    Scope - (Show below) - (Hide below)

    1.1 This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide.

    1.1.1 Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.

    1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

    This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1

    The following ASTM standards are noted as sources of useful information: Test Methods C 559, C 611, C 651, C 747, C 1025, C 1039, and E 1225.

    General Product Information - (Show below) - (Hide below)

    Committee D 02
    Document Type Guide
    Product Note Reconfirmed 2011
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 6558 : 2000 : REV A : R2015 : EDT 1 Standard Test Method for Determination of TGA CO2 Reactivity of Baked Carbon Anodes and Cathode Blocks
    ASTM D 6559 : 2000 : REV A : R2016 : EDT 1 Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5022:1979 Shaped refractory products Sampling and acceptance testing
    ASTM C 1025 : 2015 : REDLINE Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
    ASTM C 747 : 2016 : REDLINE Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance
    ASTM C 559 : 2016 : REDLINE Standard Test Method for Bulk Density by Physical Measurements of Manufactured Carbon and Graphite Articles
    ASTM C 651 : 2015 : REDLINE Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature
    ASTM E 1225 : 2013 : REDLINE Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective