ASTM D 6393 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Bulk Solids Characterization by Carr Indices
Hardcopy , PDF
24-05-2021
English
17-11-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers an apparatus and procedures for measuring properties of bulk solids, henceforth referred to as Carr Indices.2
1.2This test method is suitable for free flowing and moderately cohesive powders and granular materials up to 2.0 mm in size. Materials must be able to pour through a 6.0 to 8.0-mm diameter funnel outlet when in an aerated state.
1.3This method consists of eight measurements and two calculations for Carr Indices as follows. Each measurement, or calculation, or combination of them, can be used to characterize the properties of bulk solids.
1.3.1Measurement of Carr Angle of Repose
1.3.2Measurement of Carr Angle of Fall
1.3.3Calculation of Carr Angle of Difference
1.3.4Measurement of Carr Loose Bulk Density
1.3.5Measurement of Carr Packed Bulk Density
1.3.6Calculation of Carr Compressibility
1.3.7Measurement of Carr Cohesion
1.3.8Measurement of Carr Uniformity
1.3.9Measurement of Carr Angle of Spatula
1.3.10Measurement of Carr Dispersibility
1.4All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.4.1The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives: and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.5Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 8135 : 2017 | Standard Guide for Selection of Substitute, Non-hazardous, Particulate Solid Filling Substances for Packagings Subjected to the United Nations Performance Tests |
| ASTM C 1770 : 2013 | Standard Test Method for Determination of Loose and Tapped Bulk Density of Plutonium Oxide |
| ASTM C 1770 : 2021 | Standard Test Method for Determination of Loose and Tapped Bulk Densities of Small Quantities of Plutonium Oxide |
| ASTM D 2216 : 2005 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 653 : 2007 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 2216 : 2010 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 3740 : 2012 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2019 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2004 : REV A : EDT 1 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2008 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2013 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 6026 : 2006 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 1999 : REV C | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2020 : EDT 1 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1999 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2011 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2001 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2010 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 2216 : 2019 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 6026 : 1996 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2004 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2001 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 3740 : 2012 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2003 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 2216 : 1998 | Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 2216 : 1971 | Standard Method of Laboratory Determination Of Moisture Content Of Soil |
| ASTM D 6026 : 2001 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2004 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.