• Shopping Cart
    There are no items in your cart

ASTM D 6439 : 2011 : R2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems

Available format(s)

Hardcopy , PDF

Superseded date

07-08-2023

Superseded by

ASTM D 6439 : 2023

Language(s)

English

Published date

07-07-2017

€74.48
Excluding VAT

CONTAINED IN VOL. 05.03, 2017 Defines types of contaminants, oil purification devices, contamination monitoring, contamination control during building or refurbishing of turbine systems, lubrication system flushing, and maintenance of pure lubrication oil.

Committee
D 02
DocumentType
Guide
Pages
18
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This guide covers types of contaminants, oil purification devices, contamination monitoring, contamination control during building or refurbishing of turbine systems, lubrication system flushing, and maintenance of pure lubrication oil.

1.2To obtain maximum operating life and reliability, or lubricants and system, it is vital that the turbine lubrication system has pure oil. This guide is intended to aid the equipment manufacturer, installer, and turbine operator in coordinating their efforts to obtain and maintain clean lubrication and control systems. These systems may be on land or marine turbine generators and propulsion and mechanical drive equipment. This guide is generalized due to variations in the type of equipment, builder's practices, and operating conditions.

1.3This guide primarily addresses petroleum based lubricating oil. For systems using nonpetroleum based fluids, this guide may not be appropriate. For nonpetroleum products, consult the equipment and fluid manufacturers.

1.4This guide is applicable to both large and small lubrication systems. Some equipment specified herein, however, may not be appropriate for all systems. Moreover, in situations where specific guidelines and procedures are provided by the equipment manufacturer, such procedures should take precedence over the recommendations of this guide.

1.5This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D 4304 : 2022 Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines
ASTM D 7720 : 2021 Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
ASTM D 8506 : 2023 Standard Guide for Microbial Contamination and Biodeterioration in Turbine Oils and Turbine Oil Systems
ASTM D 7720 : 2011 : R2017 Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
ASTM D 4378 : 2013 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 4304 : 2017 Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines

ASTM D 4898 : 1990 : R2010 : EDT 1 Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis
ASTM D 4248 : 1998 Standard Practice for Design of Steam Turbine Generator Oil Systems
ASTM D 4378 : 2003 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 974 : 2014 : EDT 2 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 974 : 2001 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4898 : 1990 : R2010 Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis
ASTM D 4898 : 2016 Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis
ASTM D 7155 : 2006 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ASTM D 6971 : 2022 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 664 : 2017 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 4898 : 2016 : REDLINE Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis
ASTM D 6304:2016 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM D 7546 : 2015 : REDLINE Standard Test Method for Determination of Moisture in New and In-Service Lubricating Oils and Additives by Relative Humidity Sensor
ASTM D 4378 : 2012 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6971 : 2009 : R2014 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2004 : REV A : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 974 : 2022 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 6810 : 2002 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in HL Turbine Oils by Linear Sweep Voltammetry
API 614 : 2008 LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES
ASTM D 445 : 2021 : EDT 2 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6971 : 2009 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2007 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration (Withdrawn 2016)
ASTM D 974 : 2021 Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 6304 : 2004 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 445 : 2017 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6810 : 2013 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6304 : 2016 : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
ASTM D 4378 : 2020 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 6304 : 2004 : REV A Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 445 : 1988 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)
ISO 4572:1981 Hydraulic fluid power — Filters — Multi-pass method for evaluating filtration performance
ASTM D 6304 : 2004 : EDT 1 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 4241 : 1998 Standard Practice for Design of Gas Turbine Generator Lubricating Oil Systems
ASTM D 7155 : 2011 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ASTM D 7647 : 2010 : R2018 Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction
ASTM D 6304 : 2000 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 4248 : 1998 : R2003 Standard Practice for Design of Steam Turbine Generator Oil Systems (Withdrawn 2008)
ASTM D 664 : 1995 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 7647 : 2010 Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction
ASTM D 7546 : 2009 Standard Test Method for Determination of Moisture in New and In-Service Lubricating Oils and Additives by Relative Humidity Sensor
ASTM D 2272 : 1998 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6810 : 2022 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 7155 : 2020 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ISO 3722:1976 Hydraulic fluid power — Fluid sample containers — Qualifying and controlling cleaning methods
ASTM D 4898 : 1990 : R2000 : EDT 1 Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis
ASTM D 6810 : 2007 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 4378 : 2022 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 2272 : 2014 : REV A Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 4378 : 2013 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 445 : 2019 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6304 : 2003 Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration
ASTM D 7546 : 2015 Standard Test Method for Determination of Moisture in New and In-Service Lubricating Oils and Additives by Relative Humidity Sensor
ASTM D 4378 : 2008 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 2272 : 2009 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 7155 : 2018 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ASTM D 445 : 2001 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
ASTM D 2272 : 2014 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 664 : 2011 : REV A Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6971 : 2004 Standard Test Method for Measurement of Hindered Phenolic and Aromatic Amine Antioxidant Content in Non-zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 2272 : 2022 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 2272 : 2002 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 4378 : 1997 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
ASTM D 445 : 2018 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4241 : 1998 : R2003 Standard Practice for Design of Gas Turbine Generator Lubricating Oil Systems (Withdrawn 2008)
ISO 4021:1992 Hydraulic fluid power — Particulate contamination analysis — Extraction of fluid samples from lines of an operating system
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2272 : 2011 Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
ASTM D 6810 : 2013 : REDLINE Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 6810 : 2021 Standard Test Method for Measurement of Hindered Phenolic Antioxidant Content in Non-Zinc Turbine Oils by Linear Sweep Voltammetry
ASTM D 4898 : 1990 : R2005 Standard Test Method for Insoluble Contamination of Hydraulic Fluids by Gravimetric Analysis

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.