ASTM D 6484/D6484M : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
11-11-2020
English
15-05-2014
CONTAINED IN VOL. 15.03, 2015 Describes the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
Committee |
D 30
|
DevelopmentNote |
Supersedes ASTM D 6484 (04/04)
|
DocumentType |
Redline
|
Pages |
20
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This test method determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers. The composite material forms are limited to continuous-fiber or discontinuous-fiber (tape or fabric, or both) reinforced composites in which the laminate is balanced and symmetric with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
11/30196213 DC : 0 | BS ISO 12817 - FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF OPENHOLE COMPRESSION STRENGTH |
ASTM D 6856/D6856M : 2003 : R2008 : EDT 1 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM D 8066/D8066M : 2017 | Standard Practice Unnotched Compression Testing of Polymer Matrix Composite Laminates |
SAE AMS 2980/1 : 2014 | CARBON FIBER FABRIC AND EPOXY RESIN WET LAY-UP REPAIR MATERIAL - PART 1 - GENERAL REQUIREMENTS |
ASTM D 6856/D6856M : 2003 : R2016 | Standard Guide for Testing Fabric-Reinforced “Textile” Composite Materials |
ISO 12817:2013 | Fibre-reinforced plastic composites — Determination of open-hole compression strength |
ASTM D 7248/D7248M : 2012 | Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens |
ASTM D 7248/D7248M : 2012 : R2017 | Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens |
ASTM D 6742/D6742M : 2017 : REDLINE | Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates |
MIL-PRF-32597 Base Document:2018 | CLEANER, POLYMER AND POLYMER MATRIX COMPOSITE (PMC) MATERIAL, NON-AQUEOUS, HAP-FREE |
SAE AMS 3970/1 : 2011 | CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 1 - GENERAL REQUIREMENTS |
ASTM D 6856 : 2003 : R2008 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM D 7615/D7615M : 2011 | Standard Practice for Open-Hole Fatigue Response of Polymer Matrix Composite Laminates |
BS ISO 12817:2013 | Fibre-reinforced plastic composites. Determination of open-hole compression strength |
ASTM D 6856 : 2003 | Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials |
ASTM E 122 : 2017 : REDLINE | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 5229/D5229M : 2014-06 | TEST METHOD FOR MOISTURE ABSORPTION PROPERTIES AND EQUILIBRIUM CONDITIONING OF POLYMER MATRIX COMPOSITE MATERIALS |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
ASTM D 2734 : 2016 : REDLINE | Standard Test Methods for Void Content of Reinforced Plastics |
ASTM D 3171 : 2015 : REDLINE | Standard Test Methods for Constituent Content of Composite Materials |
ASTM D 3039/D3039M : 2017 : REDLINE | Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.