ASTM D 6528 : 2024
Current
The latest, up-to-date edition.
Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine-Grained Soils
Hardcopy , PDF
English
01-07-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This test method defines equipment specifications and testing procedures for the measurement of constant volume strength and stress-strain characteristics of fine-grained soils after one-dimensional consolidation, using a constant rate of simple shear deformation mode of loading. The constant volume condition is equivalent to the undrained condition for saturated specimens.
1.2This test method is written specifically for devices that test rectangular parallelepiped or cylindrical specimens. Other more general devices, such as the torsional shear hollow cylinder, may be used to perform consolidated constant volume simple shear tests but are beyond the scope of this test method.
1.3This test method is applicable to testing intact, laboratory reconstituted, and compacted soils, however, it does not include specific guidance for reconstituting or compacting test specimens.
1.4It shall be the responsibility of the agency requesting this test to specify the magnitude of the vertical consolidation stress prior to constant volume shear and, when appropriate, the maximum vertical consolidation stress, which will result in an overconsolidated specimen.
1.5Units—The values stated in SI units are to be regarded as the standard. No other units of measure are included in this standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.
1.5.1In the engineering profession it is customary practice to use, interchangeably, units representing both mass and force, unless dynamic calculations (F=Ma) are involved. This implicitly combines two separate systems of units, that is, the absolute system and the gravimetric system. It is scientifically undesirable to combine two separate systems within a single standard. This test method has been written using SI units; however, inch-pound conversions are given in the gravimetric system, where the pound (lbf) represents a unit of force (weight). The use of balances or scales recording pounds of mass (lbm), or the recording of density in lb/ft3 should not be regarded as nonconformance with this test method.
1.6All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.6.1The procedures used to specify how data are collected/recorded or calculated in this test standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this test standard to consider significant digits used in analysis methods for engineering design.
1.6.2Measurements made to more significant digits or better sensitivity than specified in this standard shall not be regarded a nonconformance with this standard.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8295 : 2019 | Standard Test Method for Determination of Shear Wave Velocity and Initial Shear Modulus in Soil Specimens using Bender Elements |
| ASTM D 8296 : 2019 | Standard Test Method for Consolidated Undrained Cyclic Direct Simple Shear Test under Constant Volume with Load Control or Displacement Control |
| ASTM F 3339 : 2020 | Standard Guide for Construction or Renovation of Native-soil Athletic Fields |
| ASTM D 653 : 2024 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2024 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.