ASTM D 6622 : 2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
Hardcopy , PDF
11-11-2014
English
10-01-2001
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 04.04, 2015 Describes the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces.
| Committee |
D 08
|
| DocumentType |
Guide
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2001
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces.
1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
| ASTM E 2266 : 2011 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM D 7492/D7492M : 2016 : REV A | Standard Guide for Use of Drainage System Media with Waterproofing Systems |
| ASTM C 981 : 2005 : R2013 | Standard Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks |
| ASTM D 2178 : 2004 | Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing (Withdrawn 2013) |
| ASTM D 227 : 2003 | Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing |
| CGSB 37.51 : M90 | APPLICATION FOR HOT-APPLIED RUBBERIZED ASPHALT, FOR ROOFING AND WATERPROOFING |
| ASTM D 1668 : 1997 : REV A : R2006 | Standard Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing |
| CGSB 37.50 : M89 | HOT APPLIED, RUBBERIZED ASPHALT FOR ROOFING AND WATERPROOFING |
| ASTM D 6451 : 1999 | Standard Guide for Application of Asphalt Based Protection Board |
| ASTM D 173 : 2003 | Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing |
| ASTM D 41 : 2005 | Standard Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing |
| ASTM D 1327 : 2004 | Standard Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing |
| ASTM D 2822 : 2005 | Standard Specification for Asphalt Roof Cement, Asbestos Containing |
| ASTM D 6152 : 1999 | Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.