ASTM D 6875 : 2018 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor
13-04-2023
English
22-01-2018
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 06.04, 2018 Defines a general procedure for determining the solidification point of most organic chemicals having appreciable heats of fusion and solidification points between 4 and 41 degrees C.
| Committee |
D 16
|
| DocumentType |
Redline
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers a general procedure for determining the solidification point of most organic chemicals having appreciable heats of fusion and solidification points between 4 and 41°C.
Note 1:Other test methods for determining freeze point and solidification point of aromatic hydrocarbons include Test Methods D852, D1015, D1016, D3799, D4493, and D6269.
1.2This test method is applicable to relatively pure compounds only. Solidification point depression is dependent on impurity concentrations.
1.3The following applies to all specified limits in this test method: for purposes of determining conformance with applicable specifications using this test method, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right hand digit used in expressing the specification limit, in accordance with the “rounding-off method” of Practice E29.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 8, Hazards.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 6269 : 1998 | Test Method for Solidification Point of <I>p</I>-Xylene |
| ASTM D 3852 : 2016 : REDLINE | Standard Practice for Sampling and Handling Phenol, Cresols, and Cresylic Acid |
| ASTM D 3438 : 2015 : REDLINE | Standard Practice for Sampling and Handling Naphthalene, Maleic Anhydride, and Phthalic Anhydride |
| ASTM D 4493 : 2016 : REDLINE | Standard Test Method for Solidification Point of Bisphenol A<brk/>(4,4<emph type="ital" >′</emph>-Isopropylidenediphenol) |
| ASTM D 1016 : 2005 : EDT 1 | Standard Test Method for Purity of Hydrocarbons from Freezing Points |
| ASTM D 852 : 2016 : REDLINE | Standard Test Method for Solidification Point of Benzene |
| CFR 29(PT1910.1000 TO END) : 0 | LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR |
| ASTM D 3437 : 2015 : REDLINE | Standard Practice for Sampling and Handling Liquid Cyclic Products |
| ASTM D 3799 : 1995 | Standard Test Method for Purity of Styrene by Freezing Point Method (Withdrawn 2000) |
| ASTM D 4297 : 2015 : REDLINE | Standard Practice for Sampling and Handling Bisphenol A<brk/>(4,4<emph type="ital" >′</emph> -Isopropylidinediphenol) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.