ASTM D 7140/D7140M : 2013 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method to Measure Heat Transfer Through Textile Thermal Barrier Materials
Hardcopy , PDF
23-08-2022
English
17-08-2017
CONTAINED IN VOL. 07.02, 2017 Defines the evaluation of heat transfer of textile materials which are used as thermal barriers when exposed to a calibrated convective and radiant energy heat source for 60 s.
Committee |
D 13
|
DevelopmentNote |
Supersedes ASTM D 7140. (04/2013)
|
DocumentType |
Test Method
|
Pages |
7
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the evaluation of heat transfer of textile materials which are used as thermal barriers when exposed to a calibrated convective and radiant energy heat source for 60 s.
1.1.1This standard is used to determine if the heat transfer is sufficient to ignite flammable materials which are contiguous to the textile thermal barriers.
1.2This standard is used as a means to differentiate textile materials.
1.3This test method is not intended to measure the insulation properties of materials used in protective clothing.
1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4391 : 1993 : REV A : R2000 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 1993 : REV A : R2006 | Standard Terminology Relating to The Burning Behavior of Textiles |
CFR 16(PTS1000-END) : 0 | COMMERCIAL PRACTICES - FEDERAL TRADE COMMISSION - CONSUMER PRODUCT SAFETY COMMISSION |
ASTM D 4391 : 1993 : REV A : R2013 : EDT 2 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 1993 : REV A : R2006 : EDT 1 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 2018 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 2018 : REV A | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 2016 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 4391 : 1993 : REV A : R2013 | Standard Terminology Relating to The Burning Behavior of Textiles |
ASTM D 123 : 2001 | Standard Terminology Relating to Textiles |
ASTM D 4391 : 2016 : EDT 1 | Standard Terminology Relating to The Burning Behavior of Textiles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.