ASTM D 75/D75M : 2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Sampling Aggregates
Available format(s)
Hardcopy , PDF
Superseded date
12-11-2019
Superseded by
Language(s)
English
Published date
19-06-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
This practice covers sampling of coarse and fine aggregates for the following purposes:
Preliminary investigation of the potential source of supply.
| Committee |
D 04
|
| DocumentType |
Standard Practice
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers sampling of coarse and fine aggregates for the following purposes:
1.1.1Preliminary investigation of the potential source of supply,
1.1.2Control of the product at the source of supply,
1.1.3Control of the operations at the site of use, and
1.1.4Acceptance or rejection of the materials.
Note 1—Sampling plans and acceptance and control tests vary with the type of construction in which the material is used.
1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2—The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Practice D3666 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3666 alone does not completely assure reliable results. Reliable results depend on many factors; following the suggestions of Practice D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
| ASTM C 404 : 2018 | Standard Specification for Aggregates for Masonry Grout |
| ASTM C 1777 : 2020 | Standard Test Method for Rapid Determination of the Methylene Blue Value for Fine Aggregate or Mineral Filler Using a Colorimeter |
| ASTM C 586 : 2019 | Standard Test Method for Potential Alkali Reactivity of Carbonate Rocks as Concrete Aggregates (Rock-Cylinder Method) |
| ASTM D 6825 : 2021 | Standard Guide for Placement of Riprap Revetments |
| ASTM D 448 : 2012 : R2022 | Standard Classification for Sizes of Aggregate for Road and Bridge Construction |
| ASTM C 87/C87M : 2017 | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
| ASTM C 1451 : 2018 | Standard Practice for Determining Variability of Concrete-Making Materials From a Single Source |
| ASTM D 1864/D1864M : 1989 : R2017 | Standard Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs |
| ASTM D 5284 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid |
| ASTM C 40/C40M : 2020 | Standard Test Method for Organic Impurities in Fine Aggregates for Concrete |
| ASTM D 5744 : 2018 | Standard Test Method for Laboratory Weathering of Solid Materials Using a Humidity Cell |
| ASTM C 1293 : 2020 : REV A | Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM D 7196 : 2018 | Standard Test Method for Raveling Test of Cold-Mixed Emulsified Asphalt Samples |
| ASTM D 5013 : 2018 | Standard Practices for Sampling Wastes from Pipes and Other Point Discharges |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM D 2940/D2940M : 2020 | Standard Specification for Graded Aggregate Material for Bases or Subbases for Highways or Airports |
| ASTM C 897 : 2015 : R2020 | Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters |
| ASTM C 295/C295M : 2019 | Standard Guide for Petrographic Examination of Aggregates for Concrete |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM D 6704 : 2022 | Standard Test Method for Determining the Workability of Asphalt Cold Mix Patching Material |
| ASTM D 8237 : 2021 | Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures with the Four-Point Beam Fatigue Device |
| ASTM C 332 : 2017 | Standard Specification for Lightweight Aggregates for Insulating Concrete |
| ASTM D 1139/D1139M : 2022 | Standard Specification for Aggregate for Single or Multiple Asphalt Surface Treatments |
| ASTM D 8021 : 2020 | Standard Guide for Blast Furnace and Steel Furnace Slag as Produced During the Manufacture of Iron and Steel |
| ASTM D 6932/D6932M : 2021 | Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Asphalt Mixtures |
| ASTM D 7762 : 2018 : EDT 1 | Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash |
| ASTM D 1865/D1865M : 2009 : R2017 | Standard Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs |
| ASTM E 2788/E2788M : 2018 | Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems |
| ASTM D 3987 : 2012 : R2020 | Standard Practice for Shake Extraction of Solid Waste with Water |
| ASTM D 692/D692M : 2020 | Standard Specification for Coarse Aggregate for Asphalt Paving Mixtures |
| ASTM C 330/C330M : 2017 : REV A | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 535 : 2016 | Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM D 4215 : 2021 | Standard Specification for Cold-Mixed, Cold-Laid Asphalt Paving Mixtures |
| ASTM D 6234 : 2013 : R2020 | Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure |
| ASTM D 8262 : 2022 | Standard Test Method for Determining the pH of Granular Material for Use in Embankments, Subgrades, and Retaining Wall Backfil |
| ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 1761/C1761M : 2017 | Standard Specification for Lightweight Aggregate for Internal Curing of Concrete |
| ASTM D 8378/D8378M : 2021 | Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave |
| ASTM D 8038 : 2016 : R2022 : EDT 1 | Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material |
| ASTM E 1109 : 2019 | Standard Test Method for Determining the Bulk Density of Solid Waste Fractions |
| ASTM D 7370/D7370M : 2014 : R2021 | Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse, and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion |
| ASTM D 2419 : 2022 | Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate |
| ASTM D 4793 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Water |
| ASTM D 8012 : 2018 | Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications |
| ASTM C 29/C29M : 2017 : REV A | Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate |
| ASTM D 6307 : 2019 | Standard Test Method for Asphalt Content of Asphalt Mixture by Ignition Method |
| ASTM C 88/C88M : 2018 | Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate |
| ASTM D 7655/D7655M : 2012 : R2022 | Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems |
| ASTM C 566 : 2019 | Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying |
| ASTM C 641 : 2017 | Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates |
| ASTM D 4125/D4125M : 2021 | Standard Test Methods for Asphalt Content of Asphalt Mixtures by the Nuclear Method |
| ASTM D 3744/D3744M : 2018 | Standard Test Method for Aggregate Durability Index |
| ASTM D 8155 : 2017 | Standard Practice for Shake Extraction of Solid Mining and Metallurgical Processing Waste with Water |
| ASTM D 4791 : 2019 | Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate |
| ASTM C 1356 : 2007 : R2020 | Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure |
| ASTM E 889 : 1982 : R2023 | Standard Test Method for Composition or Purity of a Solid Waste Materials Stream |
| ASTM C 35 : 2001(R2019) | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| ASTM D 5081/D5081M : 1990 : R2018 | Standard Test Method for Aggregate Layer Hiding Power |
| ASTM D 1073 : 2016 : R2022 | Standard Specification for Fine Aggregate for Asphalt Paving Mixtures |
| ASTM D 7000 : 2019 : REV A | Standard Test Method for Sweep Test of Emulsified Asphalt Surface Treatment Samples |
| ASTM F 2980 : 2013 : R2017 | Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF) |
| ASTM C 144 : 2018 | Standard Specification for Aggregate for Masonry Mortar |
| ASTM D 5106 : 2022 | Standard Specification for Steel Slag Aggregates for Asphalt Paving Mixtures |
| ASTM D 420 : 2018 | Standard Guide for Site Characterization for Engineering Design and Construction Purposes |
| ASTM D 6155 : 2019 | Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures |
| ASTM D 4792/D4792M : 2013 : R2019 | Standard Test Method for Potential Expansion of Aggregates from Hydration Reactions |
| ASTM C 1797 : 2017 | Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete |
| ASTM D 5233 : 1992 : R2017 | Standard Test Method for Single Batch Extraction Method for Wastes |
| ASTM D 1863/D1863M : 2005 : R2018 | Standard Specification for Mineral Aggregate Used on Built-Up Roofs |
| ASTM F 2797 : 2019 | Standard Test Method for Evaluating Edge Cleaning Effectiveness of Vacuum Cleaners |
| ASTM D 8249 : 2019 | Standard Practice for Use of Rotary Kiln Produced Porous Ceramic as a Mineral Amendment in Topsoil Used for Landscaping and Related Purposes |
| AWWA C104/A21.4:2022 | Cement–Mortar Lining for Ductile-Iron Pipe and Fittings |
| ASTM D 3666 : 2013 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2011 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2007 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3665 : 2002 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3666 : 2009 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3665 : 2012 : R2017 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3665 : 2007 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3666 : 2005 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2003 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2000 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3665 : 2012 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3666 : 2007 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2007 : EDT 2 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2003 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2001 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2006 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3665 : 2007 : EDT 1 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3665 : 2006 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3666 : 2004 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2005 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2007 : REV A : EDT 1 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3665 : 1999 | Standard Practice for Random Sampling of Construction Materials |
| ASTM D 3666 : 2009 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2002 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.