ASTM D 7685 : 2011 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for In-Line, Full Flow, Inductive Sensor for Ferromagnetic and Non-ferromagnetic Wear Debris Determination and Diagnostics for Aero-Derivative and Aircraft Gas Turbine Engine Bearings
Hardcopy , PDF
17-06-2022
English
23-11-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 05.04, 2018 Defines the minimum requirements for an in-line, non-intrusive, through-flow oil debris monitoring system that monitors ferromagnetic and non-ferromagnetic metallic wear debris from both industrial aero-derivative and aircraft gas turbine engine bearings.
| Committee |
D 02
|
| DocumentType |
Standard Practice
|
| Pages |
16
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers the minimum requirements for an in-line, non-intrusive, through-flow oil debris monitoring system that monitors ferromagnetic and non-ferromagnetic metallic wear debris from both industrial aero-derivative and aircraft gas turbine engine bearings. Gas turbine engines are rotating machines fitted with high-speed ball and roller bearings that can be the cause of failure modes with high secondary damage potential. (1)2
1.2Metallic wear debris considered in this practice range in size from 120 μm (micron) and greater. Metallic wear debris over 1000 μm are sized as over 1000 μm.
1.3This practice is suitable for use with the following lubricants: polyol esters, phosphate esters, petroleum industrial gear oils and petroleum crankcase oils.
1.4This practice is for metallic wear debris detection, not cleanliness.
1.5The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
| ASTM D 7919 : 2014 : R2017 | Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes |
| ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 7917 : 2014 : R2018 | Standard Practice for Inductive Wear Debris Sensors in Gearbox and Drivetrain Applications |
| ASTM D 7720 : 2021 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
| ASTM D 7898 : 2014 : R2020 | Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery |
| ASTM D 7919 : 2014 : R2021 | Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes |
| ASTM D 8128 : 2017 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
| ASTM D 7898 : 2014 | Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.