ASTM D 8135 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Guide for Selection of Substitute, Non-hazardous, Particulate Solid Filling Substances for Packagings Subjected to the United Nations Performance Tests
Hardcopy , PDF
25-03-2023
English
03-10-2017
CONTAINED IN VOL. 15.10, 2017 Specifies the selection, use and description criteria of non-hazardous particulate solid substitutes used to replace hazardous materials for the purpose of performance testing packagings.
Committee |
D 10
|
DocumentType |
Guide
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1The purpose of this guide is to clarify the selection, use and description criteria of non-hazardous particulate solid substitutes used to replace hazardous materials for the purpose of performance testing packagings. This includes identification of the physical parameters of substitute non-hazardous solid test fill materials that may affect packaging performance and test results and should be considered when selecting and describing a test fill material that conforms to the requirements of the Hazardous Materials Regulations (HMR). This guide is intended for use with package testing procedures for particulate solid materials that have flow characteristics. It is not intended for use with hazardous articles.
1.2This guide provides information to assist packaging users, manufacturers, and performance testing service suppliers regarding the types of physical properties that should be considered when selecting substitute filling substances for the testing, certification and manufacture of packagings under the United Nations packaging protocols (UN Recommendations on the Transport of Dangerous Goods-Model Regulations) as adopted by US DOT in 49 CFR HMR.
1.3This guide provides the suggested minimum information concerning the physical characteristics of the filling substances that should be documented in the certification test report and notification to users to allow for test repeatability and analysis, and to provide guidance to the user of a packaging of pertinent physical differences between potential hazardous lading and the filling substance with which the packaging was tested.
1.4This guide does not purport to address regulatory requirements regarding the compatibility of filling substances with transport packagings. Compatibility requirements must be assessed separately, but it should be noted that under certain national and international dangerous goods regulations, the selection of the filling substances for package performance testing may be prescribed with respect to chemical compatibility requirements.
Note 1:Under the US HMR determination of packaging compatibility with a particular hazardous fill material is “the responsibility of the person offering the hazardous material for transportation” as prescribed in 49 CFR § 173.24(e).
1.5When testing packaging designs intended for hazardous materials (dangerous goods), the user of this guide shall be trained in accordance with 49 CFR §172.700 and other applicable hazardous materials regulations such as the ICAO Technical Instructions, IMDG Code, other applicable national or international dangerous goods regulations that govern the testing, manufacture and use of packagings authorized for the transportation of dangerous goods, and carrier rules such as the IATA Dangerous Goods Regulations.
1.6The units of measurement are consistent with the HMR.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7887 : 2020 | Standard Guide for Selection of Substitute, Non-hazardous, Liquid Filling Substances for Packagings Subjected to the United Nations Performance Tests |
ASTM D 7790 : 2019 | Standard Guide for Preparation of Plastic Packagings Containing Liquids for United Nations (UN) Drop Testing |
ASTM D 7481 : 2009 | Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated Cylinder (Withdrawn 2018) |
ASTM E 11 : 2020 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM D 7481 : 2018 | Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated Cylinder |
ASTM D 6393 : 2014 : REDLINE | Standard Test Method for Bulk Solids Characterization by Carr Indices |
ASTM D 6393 : 2008 | Standard Test Method for Bulk Solids Characterization by Carr Indices |
CFR 49(PTS186-199) : 0 | TRANSPORTATION |
ASTM E 11 : 2022 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ASTM D 4919 : 2017 | Standard Guide for Testing of Hazardous Materials (Dangerous Goods) Packagings |
ASTM D 6393 : 1999 | Standard Test Method for Bulk Solids Characterization by Carr Indices |
ASTM D 4919 : 2003 | Standard Specification for Testing of Hazardous Materials Packagings |
ASTM D 6393 : 2014 | Standard Test Method for Bulk Solids Characterization by Carr Indices |
ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
ISO 2234:2000 | Packaging Complete, filled transport packages and unit loads Stacking tests using a static load |
ASTM D 4919 : 1989 : R1997 | Standard Specification for Testing of Hazardous Materials Packagings |
ASTM D 4919 : 2003 : R2008 | Standard Specification for Testing of Hazardous Materials Packagings (Withdrawn 2017) |
ISO 16495:2013 | Packaging Transport packaging for dangerous goods Test methods |
CFR 49(PTS100-185) : 0 | TRANSPORTATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.